Results 1 to 15 of 15

Thread: FILE WORK patterns THAT LOOKS LIKE A VINE

  1. #1
    Join Date
    Dec 2008
    Location
    moose jaw sask canada
    Posts
    1,189

    FILE WORK patterns THAT LOOKS LIKE A VINE


    ADVERTISEMENT
    Could someone help me out as to what types of files I need to do the crawling vine on the spine of a knife Ive been doing some rather plain file work like v pattern and dots and half round spots . The vine I know is Im sure harder than it looks but Ide like to try some differnt patterns. Anyone with any they would like to share please post them here thanks kellyw

  2. #2
    Join Date
    Mar 2008
    Location
    Sacramento, CA
    Posts
    1,282
    This is a good site that tells you the files and techniques for doing vine filework. I tried it with good success.

    http://beknivessite2.homestead.com/vinefilework.html

  3. #3
    Join Date
    Nov 2004
    Location
    Central Texas
    Posts
    241
    I use a chainsaw file and a marking file. Grind the flat side of the Marking file so the edge is sharp instead of rounded. I have used a three square with one side ground flat to sharpen the edges. Hope that helps.

    Craig

  4. #4
    Join Date
    Dec 2008
    Location
    moose jaw sask canada
    Posts
    1,189
    thanks so much I went to the site and started right away im over half done one with only one small mistake but I think the next file cuts will get rid of my minor misshap. thanks kellyw

  5. #5
    Join Date
    Dec 2008
    Location
    moose jaw sask canada
    Posts
    1,189

    Big trouble on the vine

    I am having big trouble, I made the alternating round file marks . Then made them bigger, they were not as rounded off as in the picture i was looking at but I stratrd to file with the triangular file for the thorn . IT ISNT WORKING OUT . All that seems to be happening is im filing off the area and not leaving a thorn . The directions at this point are very plain and need to be more specific on angles and type of file and im making a mess out this really nice knife. the steel is cpm154 if that makes a difference cuzz its a little harder to work. help needed again . kellyw

  6. #6
    Join Date
    Oct 2006
    Location
    Syracuse NY, Will the last employed worker please turn out the lights?
    Posts
    3,224
    practice on scrap!

    -Page

  7. #7
    Join Date
    Dec 2008
    Location
    Sharpsville, Indiana
    Posts
    1,936
    Another good tutorial is at, http://rocketknives.com/fileworkvine.htm

  8. #8
    Join Date
    Dec 2004
    Location
    Valdosta, Ga
    Posts
    679
    http://smartflix.com/store/video/347/Fileworking
    Dwayne Dushane does an excellant How-To on filing available
    for rental here. The DvD is available many places for sale
    as well
    Tom
    So.Ga.

  9. #9
    Join Date
    Dec 2008
    Location
    moose jaw sask canada
    Posts
    1,189
    Thanks Jason I have done a poor job on this one but looks like barb wire . The next one will be better Ill try this method and see if its better I think my file could be part of the problem too. I am using the jewllers files in the set of like 5. Ill change to the 1/8 chain saw and a different triangle file. kellyw

  10. #10
    Join Date
    Apr 2007
    Location
    Minneapolis
    Posts
    1,060
    Quote Originally Posted by Tommegow View Post
    http://smartflix.com/store/video/347/Fileworking
    Dwayne Dushane does an excellant How-To on filing available
    for rental here. The DvD is available many places for sale
    as well
    Tom
    So.Ga.

    Ive seen this one and its really good. Think he modifies the marking file on the grinder first. Well done video.

    Larry

  11. #11
    Join Date
    Nov 2003
    Location
    Cypress, Texas
    Posts
    356
    I use 6" round and 6" half round files to do my vine patterns. These are the only two files needed, although it is nice to have them in several "grits"

    Always hold the files at a compound 45 degree angle to the blade, no matter what part of the vine pattern you are filing. I make the rounds and then cut the thorns with the half-round file. I use the flat edge for the thorn, the half round edge for the vine.

    Here is a great reference on files from Nicholson: Guide to Filing.

    I'm filing some vine patterns on six blades right now. If you need some assistance, PM me.

    Edit: I like to make initial spacings 3/8" apart.

    Mike L.

  12. #12
    Join Date
    Dec 2008
    Location
    moose jaw sask canada
    Posts
    1,189
    I went to you tube and now have the idea there are a couple people that have done video s thanks everyone im going to go try a blade . kellyw

  13. #13
    Join Date
    Dec 2008
    Location
    moose jaw sask canada
    Posts
    1,189
    WELL I went at it on a piece of scrap with big files and touched up and rounded off some stuff with needle files and its pretty good . thanks everyone the video on you tube really helped.

  14. #14
    Are any of you guys good enough to carve a row of skulls? If so, please post some pics and a how to. I think that would look sweet on the back of a blade.

    -MoF

  15. #15
    Join Date
    Dec 2008
    Location
    moose jaw sask canada
    Posts
    1,189
    I will give it a try and let you know. lmao After watching D Duchane I think anything could be done.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •