Results 1 to 9 of 9

Thread: Tightening a knife handle

  1. #1

    Tightening a knife handle


    ADVERTISEMENT
    I don't know anything about fixing knives, so I thought I would ask before I messed my old one up. I have quite a few knives, and most of them are old. One in particular has a mild (I think) problem; the handle is slightly loose.

    This is an old Marbles about 9 or 10 inches long with a 4.5 or 5 inch blade and either stag or bone handle covers. It is a beauty even though time worn and stained. I got it from a friend. I don't really care how the knives look when I get them, but once I do get them in my hands, I try to make them look better. Then, I keep them for my sons and grandchildren.

    The handle on this knife is just slightly loose. When holding the blade in my left hand, I can make the handle twist very slightly in my right hand. I would like to tighten this up; how do I do that? I don't want to damage the knife.

    On the back of the handle, everything appears to be held together with a nut with the tang right in the center. If I tighten this, will that tighten the knife handle? If so, what type of screwdriver?? do you all use to do this. I tried gently with a regular screwdriver but can't get enough traction to turn the nut. I didn't know if there is a special tool that fits over the tang and into the spaces on each side that would make this job easier or not.

    As you can tell, I know zero about how knives are made. I have had them all my life, but I never have tried making or fixing one. I would appreciate your help.

    Thanks!!

    Ray

  2. #2
    Join Date
    Jan 2010
    Location
    montana
    Posts
    327
    show us some pics and wed be able to help a little easyer

  3. #3
    Join Date
    Jun 2008
    Location
    Ca.
    Posts
    1,574
    Probably a spaner nut as on most Marbles.

    Has two recesses one on each side?

    I've made a few tools for these. Took a piece of scrap steel and measured the dimensions with caliper and formed two tabs that fit in with a Dremel tool. Clamp the tool in a vise or put vise grips on it.

  4. #4
    Probably a spaner nut as on most Marbles.

    Has two recesses one on each side?
    Yes, that's it. I took my camera home and don't have it with me at the clinic. I'll bring it back and do that, but I just checked ebay and found a picture of what I am talking about:



    Ray
    Last edited by Harold Ray; 10-30-2010 at 03:48 PM.

  5. #5
    Join Date
    Jun 2008
    Location
    Ca.
    Posts
    1,574
    Basically all you need is a piece of sheet metal that is notched to fit over the threaded part of the tang. You could do it with a cheap file.

  6. #6
    Try one of those tiny wrenches, like the one that comes with the dremel. Looks like it would fit.

  7. #7
    Join Date
    Mar 2007
    Location
    WNY
    Posts
    3,934
    I just tightened up an old edge mark with similar construction. The spanner wrenches I had didn't fit, so I used a a small pair of needle-nose pliers to crank it down. Tight as a drum now.

    Just bear in mind that the nut will be slightly recessed when you're done.

  8. #8
    Thanks, folks, I'll get that done.

    Ray

  9. #9

    tighten handle

    hi i have the same type of knife and was wondering how to tighten it once you have the tool. do you twist it or do you put the drill bit into an electric drill or by hand? if anyone could help that would be great. Thanks

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •