A knife for Mark by Markman

[Burl Source]

These are some photos of a knife being made for me by Erik Markman.
Some of the things I really like in a knife are:
Integral Bolsters
Interesting Patterns in the steel
Sculpted Handles
Ultra Clean overall
From what I have seen in Erik's knives, these are normal features.

Here is what Erik has sent so far;

First pic is welded, forged and profile ground.


On the second pic I have ground the bevels and the transition to the bolster.


A little more grinding and it is ready for heat treat.

[Salem Straub]

That's going to be super cool. I'm a big fan of integrals, the pattern looks nice too.

[David Sharp]

Can't wait to see this. There was one just posted in Custom and Handmade.

[Mike Davis]

Very nice! Waiting to see this one finished up

[erik markman]

Thanks for the introduction Mark!

Here is the progress of yesterdayevening.

After rounding the bolster to its final shape i placed the blade in my newly made clamp for grinding and filing the back of the bolster square and flat.
It has a slot on the front so I can see if the blade is in the right position and has 2 leathercoverd steel plates inside it that are pushed together by the bolts sticking through the sides. It also has a piece of allthread running through the bottom of the square tube and the plates so the don't drop out. There is a hardened steel plate on top so the file doesn't chew up the surface. It works much nicer than my old clamp wich I will show later.



Here you can see the plates clamping the blade.



After grinding away the bulk of the unneeded steel.



After filing the back of the bolster.



Here it is out of the jig, the tang is still almost half an inch thick by a little over 3/4 high, that doesn't come off easily..



Erik

[erik markman]

I ground and filed the false edge and tomorrow evening it's time to clean up the tang and grind the blade to 400 before heattreat.

[Burl Source]

I am really excited about this knife.
Thank you for your posts Erik.

[erik markman]

Ground to 400 and a quick etch to see where we are going.

[erik markman]

The smaller one is for myself. I sold my personal knife a while ago.

[erik markman]

The blade with the beautiful stabilised Redwood burl block provided by Mark.



Drilling the pilothole.



Getting there...



Sawed off the angle for the bolster with not much fitting left to do.

[jurgen]

looking good buddy !!!

[Burl Source]

Looking really good Erik!

[erik markman]

The block fitted against the bolster, the contour of the handle scribed and ready to drill the pinhole.



The blades painted in antiscale compound and my HT oven heating up.




Quenchoil heating up. This is Durixol 25W wich is a professional HT oil, I have been using it for almost a year now and it is a great improvement over peanutoil in hardness and keeping things straight.



The blades as-quenched, nice and straight and free of scale. Lucky me......

[Burl Source]

This is looking great Erik.
I am really looking forward to seeing when you start sculpting the handle.

[ChapmanPreferred]

Very sweet!

[Fiddleback]

Man, I'm loving that knife. Great thread.

[erik markman]

Here is the block ground to profile and the lines for the contour scribed.



Roughly ground to shape.



With the template I use for these knives.



The corners knocked off and roughly shaped.



I make sure i keep the centerlines on top and bottom so it is easier to keep things symetrical.



Now it is time to finish the blade. I like a flatground blade so I use a DMT diamondplate to take out scratches and high spots to get things really FLAT.
This is after a few wipes and it was almost flat already.

[tedinatl]

This is great! Thanks for taking the time to put this together, Erik!

Hartelijk bedankt!

[erik markman]

Graag gedaan!

[Burl Source]

The knife is really looking good Erik!