Closed blade wobble

N

NamDoc

Joined
Oct 17, 2015
Messages
4
Hi all, new here, got my first Buck 110 when I went to Vietnam in 1965, got my present one this week. Boy what a difference.......:eek:

I recently acquired my new 110. Just asking if this is normal. When the blade is closed it easily moves from side to side yet when opened locks up tight , releasing the lock while open and the blade gets quite a bit of play.
 
Welcome to the forums.....I've noticed this in a few of my different lockbacks, and I've never found it to be an issue whatsoever. As long as you are locked up tight with the blade open, I think you're fine. It's pretty common for some knives to have a bit of movement side to side as well when open, but just very slight. Go forth and enjoy your new 110.....and should it get worse or really bother you, Buck will be happy to look it over for you.
 
I had this problem (and others) on my 112, I sent it back and got it replaced.
 
Not an issue to me. If the knife stays closed and locks open with no play I don't really care if it has some play in the closed position. I don't use it when it's closed.
 
I don't use it in closed position, but with this bad a wobble, what is it going to be like after use. But then again it has become a cheap knife over the years. My first was in 1965, this is not the same knife, just looks the same
 
Admittedly I only have a couple of Bucks (yet), but none of them have blade wobble like described. Certainly my 110 is rock-solid. I would think if you sent it in to Buck with a note describing your concern they would take care of it. Could be as simple as tightening some pins.
 
TAH said:
Or look for a 60s/70s model. :)
Click to expand...

That's true. I just figured if the OP feels the current 110 has become a "cheap knife" there isn't much sense in getting another one. Tracking down an older model might be a good option though IMHO there really isn't much different about the 110 made today versus the first one at least as far as the original design. Yes, the steel is different as are the slab material but overall I don't see where any significant changes have been made. The way the brass frame was made has changed as I recall but it's still pretty much the same knife all these years. I'm actually surprised Buck has been able to keep the price down like they have when so many other things have increased in price.
 
Badhammer said:
That's true. I just figured if the OP feels the current 110 has become a "cheap knife" there isn't much sense in getting another one. Tracking down an older model might be a good option though IMHO there really isn't much different about the 110 made today versus the first one at least as far as the original design. Yes, the steel is different as are the slab material but overall I don't see where any significant changes have been made. The way the brass frame was made has changed as I recall but it's still pretty much the same knife all these years. I'm actually surprised Buck has been able to keep the price down like they have when so many other things have increased in price.
Click to expand...

You're certainly correct. I just thought the OP might be happier with one closer to his first. :)
 
We need to start a Buck wiki where we can gather all the collective wisdom of this board.
 
Joe58 said:
Kinda off topic, apologies, but what're the 440C years please? Like to get one.
Click to expand...

Joe, look for a "Two Dot" •110• tang stamp - it'll be 440C - usually fairly easy to find and not overpriced. I cleaned a deer this past Monday with a Four Dot - I like it because the edge holds well but is easy to touch up with ceramic rods - however it is 425MOD (I think). OH

Ps This picture is of my Two Dot, but maybe hard to see the stamp.

Buck_110_two-dot_ca_1974-80.JPG
 
Last edited:
NamDoc said:
Hi all, new here, got my first Buck 110 when I went to Vietnam in 1965, got my present one this week. Boy what a difference.......:eek:

I recently acquired my new 110. Just asking if this is normal. When the blade is closed it easily moves from side to side yet when opened locks up tight , releasing the lock while open and the blade gets quite a bit of play.
Click to expand...

Again, Welcome to the Buck Forum NamDoc.

Your 1965 110 would be among the very first variations of the 110 and WAY more valuable than what you gave for it. Would be fun to see pics of it, and what it went through in nam.

Don't forget about the Buck Forever warranty. Should your new 110 fail for near any reason, Buck will fix it, as been attested to by many of us here that have sent knives back to Buck for various reasons. I sent a 110 back once for some piddly reason that wasnt a major problem. Not expecting it, Buck returned me a new one.

Like others have said, Buck will take care of it.

Post us some pics of that oldie, then retire it to a display shelf. Sounds like it deserves it.
 
I second the request for some pics of the '65 110. Regarding the closed wobble, that is not an issue to me. When it comes to Buck, all I expect is a safe and functional knife, nothing more nothing less. If I want precision I'll grab my sebenza.
For it's cost and being American made, I think it is well worth the price.
Now if it is rubbing the liners on the other hand...
 
You must log in or register to reply here.
Back
Top