Correct way to peen a liner lock ??

J

Jamesh Bond

Joined
Jan 14, 2007
Messages
1,760
In the spirit of always being prepared, I'm interested in how one would properly peen a worn liner. I had posted a similar question in Knifemakers Discussion months ago, but responses were more flavored around me building a knife. While I think this is a great idea, and have long wanted to do so at some point, presently it isnt remotely realistic, and i suspect my specific inquiry doesn't require an entire build. So I'm asking in this subforum where the focus might be a little nearer to my own.

FWIW, i have studied Bob Terzoulas tactical folder book, and am comfortably familiar with linerlock principles and construction.

So, how is peeing a liner properly done ???


Thx much.
 
I don't always pee on my my liner locks, but when I do I drink Dos Equis first. Stay sharp my friends.
That's quick AND dirty...
Russ
 
a brass or nickel rod and patgience with a small, very small hammer or a spoon from the kitchen. it will dome fairly easy. same principle used on straight razors.
 
Late lockup, and possibly rock, depending, Doc.

Kn4wd, you explained what peening is, which i already know. But how and where does one peen without affecting the detent ? And can you elaborate the straight razor reference? I don't follow.

Does anyone actually know the proper way?

Thx.
 
mycough said:
I don't always pee on my my liner locks, but when I do I drink Dos Equis first. Stay sharp my friends.
That's quick AND dirty...
Russ
Click to expand...

Hmmm.
You don't always drink when posting, but when you do, it ends up in my thread in the wee hours of the morning. Lol.
 
I would imagine if done to correct late lock up you are going to want to slightly lengthen the lock bar. I would think you would want to peen it on the side of the bar near to to lock face. Try sending Charlie Mike a pm. I think I remember him talking about this once upon a time.
 
Here's how I do it-

Place the lock flat on a hard, sturdy, flat steel surface (anvil, vise, block of steel) detent side up, then I place a large pin punch evenly flat over the edge of the lock face and hit the punch with a hammer just once (striking on the detent side). Then I assemble the knife and check the results. Then repeat the process if necessary until I get it just right.
 
That's what I was thinking. My main concern is making sure the detent isn't affected. Read about that happening once.

Hey doc, hoping CM chimes in, but i dont think i can PM.

Thx guys.
 
Check out Steve Rice (our own STR here) youtube. He showed exactly what killgar said.
Edit to add: https://m.youtube.com/watch?v=lQ_alRnX324

Have you checked the stop pin? Sometimes it's caused by stop pin being flattened due to blade tang impact (hard flicking can cause this). Rotating it to new spot will improve the lockup.
 
Last edited:
Chris "Anagarika";15458162 said:
Check out Steve Rice (our own STR here) youtube. He showed exactly what killgar said.
Edit to add: https://m.youtube.com/watch?v=lQ_alRnX324

Have you checked the stop pin? Sometimes it's caused by stop pin being flattened due to blade tang impact (hard flicking can cause this). Rotating it to new spot will improve the lockup.
Click to expand...
good call on the stop pin, been a quick fix more than once... Russ
 
To clarify guys, I'm not having an issue. This is just a knowledge quest to prepare for contingincies.

Aware of the stop pin trick too.


I run against the grain here. I'm actually a linerlock fan. I'm also heavy into simplicity, DIY, and saving money, therefore enjoy anything conducive therein.

Appreciated much !

EDIT: Woot! STR's video is EXACTLY what I was looking for! THX AGAIN ALL !!!!!
 
Last edited:
Killgar is correct.
 
You must log in or register to reply here.
Back
Top