questions about spyderco delica

Capt. Carl

Capt. Carl

Gold Member
Joined
Jun 16, 2006
Messages
1,665
Ok, I am going to buy one of these knives but I have a few questions first... How do you know if it is a generation 4 and which blade is more recommended, the spyderblade (serrated) or the plain blade.. This will be used as an EDC.
 
Well, I really don't know what to get with reguards to the type of blade...I have 2 plain edge kershaw speed safes (chive and leek).
 
Generation 4 and 3 are very different.
FRN gen4 has liners and gen3 does not
SS generation 4 blade steel is VG10 and gen3 blade steel is AUS6
Shape of the blade is also little different; tip of the blades on gen3 looks pointier.
Choice of plain edge or Spyderedge depends on your use of the knife. It was a lot of threads about this. Basically, Spyderedge is much better if you need to cut something like ropes, belts or cardboard.
Goog luck in your quest
 
I instead bought the buck knives police knife thanks to oregon. What a sweet deal! but i still want to buy the delica in the future.

thank you for the help bh49.
 
I find I like plain edge much better for EDC. But why take my word for it? If you don't own any serrated blades, it might not be a bad idea to get yourself a serrated delica to decide for yourself. Again, though, I feel plain edge is usually more suitable if you're just carrying a single EDC.
 
If you are buying over the internet I suggest you go to a dealer that specifically states that it is the new Delica 4. If it just says Delica then chances are it is the older model. But, the older model is not too shabby.
 
I have a pointy old style serrated in VG-10 that I would not part with.

Actually I ..would ... part with it as I have parted a lot of stuff with it.

I didn't think I would like fully serrated, but once you have used one, you will be hooked. Or serrated, whichever the case may be.

:)
 
The good ....OLD.... one looks like this"

spyderco5du.jpg
 
I am buying the Delica 4 tomorrow. Plain edge for me.

I prefer plain edge for: sharpening pencils, carving wood, making sandwiches. first aide stuff, sharpening on a stone.

If I were cutting alot of rope I would opt for serrations.
 
Capt. Carl said:
How do you know if it is a generation 4
Click to expand...
The easiest way I can think of is: if the handle is held together with small, silver-colored screws, it's the 4th generation model.

In case you're interested (any Spydie experts out there please correct me if I'm wrong here):
  • First Generation: zytel handles without liners, integral zytel pocket clip, pointy hollow-ground blade
  • Second Generation: smooth stainless steel handles, steel pocket clip held on with three screws
  • Third Generation: zytel handles without liners, steel ambidextrous pocket clip held on with a single large "coin slot" screw, flat ground blade
  • Fourth Generation: zytel handles with nested steel liners and visible screws, four-way LH/RH top up/down pocket clip, flat ground blade with dropped tip
How'd I do? :D

and which blade is more recommended, the spyderblade (serrated) or the plain blade.
Click to expand...
My first couple of Spydercos were serrated, but these days I prefer a plain edge for general EDC use. On a blade as short as the Delica, too, a combo-edge leaves too little of either plain or serrated edge, so I'd avoid that, too.
 
Depends what you plan to use the knife for. For most everyday use, a PE is usually more recommended.
 
I am going to take my knives to be sharpened at the bass pro shops, if I were to get a spyderedge, would it be more likely for them to mess it up because it is harder to sharpen?
 
Also, what are your experiences with the delica 4 vs. the native III...I gotta choose between one..either the delica 4 for $39.00 or the native III for $44.00. Plus shipping of course.
 
May be, consider to buy a Sharpmaker; it is about $45 (comes with DVD and manual). After watching DVD (about 30 minutes) you will sharpen serrated or plain edge knife easy. It is fan and saved money you will spend on knives. I have it for 8 month and this is the best $45 spend
Good luck
 
I was thinking about getting a sharpmaker, but wouldnt it be better to just spend a few dollars every once and a while and get it sharpened on the wheel?
 
The easiest way to check for Delica 4 or Endura 4 is to look for the 4 way pocket clip holes. There are 3 holes on each of the 4 corners of the handle. That's how we do it quickly here.

I always recommend plain edges for people who can and will maintain them and partially serrated edges for people who can't or won't. Good luck with the knife.
 
Capt. Carl said:
I was thinking about getting a sharpmaker, but wouldnt it be better to just spend a few dollars every once and a while and get it sharpened on the wheel?
Click to expand...

The wheel is the worst way to sharpen a knife in my experience because it removes more steel than necessary causing the blade to wear out sooner than it might otherwise. It is fast. That's the trade off.

Personally, I'm not a fan of V sharpeners because they can do some maintenance but aren't a good choice for grinding bevels. But they are sure better than subjecting your knife to a power driven sharpener over and over. Since you're interested in knives, I think it would pay for you to learn about and gain some skill in blade sharpening. It isn't rocket science and you may find it an enjoyable pursuit. I do. Take care.
 
I guess it's time to mention that I carry the fully serrated one WITH a Fallkniven plain edge for when I want regular edge use.

But for ZIPPING through stuff, NOTHING beats the serrations.

So, I carry both edges at all times.

Oh yeah, the serrated Delica is plain edge for about the 1st 3/4 inch for pencil sharpening. AND chisel grind even if on wrong side for a right hander.
 
You must log in or register to reply here.
Back
Top