Users: Cold Steel, Spyderco, Kershaw/ZT, Benchmade

Noctis3880

Noctis3880

Joined
Jul 22, 2009
Messages
11,409
Notes:
-All knives unless otherwise noted have been carried, used, and sharpened.
-Shipping via USPS Priority Insured w/tracking to CONUS only.
-Please allow 2-3 days for delivery due to work schedule.
-Paypal personal or add 4%.
-No Money Orders.
-Not interested in trades.

Cold Steel Talwar
Blade has been scuffed slightly on both sides from rubbing against the inside of the handles. Could be possible to buff off, but that could be difficult to do without buffing off the print on the blade(bead blasting would make it more resistant to scratching). Titanium bolster has also been scuffed a little from pocket carry. Lock is a bit stiff, making one-handed opening near impossible(also makes wave opening unreliable), and closing may hurt slightly due to notches in the lockback bar. Edge has been stropped on diamond paste, but the factory grind lines are still clearly visible. This has not been seriously sharpened or used, just carried. Includes hard storage case and extra clip/screws.

Price is $175$150SOLD shipped.
 

Attachments

  • P1010064.JPG
    P1010064.JPG
    44.2 KB · Views: 87
  • P1010071.JPG
    P1010071.JPG
    24.1 KB · Views: 56
  • P1010070.JPG
    P1010070.JPG
    31.6 KB · Views: 59
  • P1010065.JPG
    P1010065.JPG
    22.7 KB · Views: 60
  • P1010063.JPG
    P1010063.JPG
    40.6 KB · Views: 72
Last edited:
Benchmade 710-1

Limited Run in M390 steel. Thumb studs have been slightly ground from sharpening(hard to tell unless it's right in front of your eyes). #247 of 250

Price is $190$175 shipped.

Benchmade 480-1 Shoki

Limited Run in M390 steel. Thumb stud is slightly ground from sharpening(again, hard to tell unless it's in front of your eyes). #118 of 500.

Note: Lock can be disengaged by pushing the blade closed. I'm not sure if this is a faulty lock or a poor lock design, but given the small size of the blade, I don't find it much different than a SAK.

Price is $125$100 shipped.
 
Last edited:
Spyderco Manix 2 CTS-XHP Sprint Run
The blade has been mirror polished by me, though there is still somewhat of an orange peel texture to it. Edge was sharpened by Jim Ankerson on the Edge Pro to a mirror polish, please exercise caution with it.

Price is $200$175 shipped.

Spyderco Gayle Bradley(old version)
This is the old version with full stainless liners(non-skeletonized). Blade has been polished with somewhat of an orange peel texture(tried going for a mirror finish, but it proved very stubborn).

Price is $110$100 shipped.
 
Last edited:
Zero Tolerance 0350CB
This is the limited run in Elmax/14C28N composite. Blade has been slightly polished, not very evenly though. This one came back from Kershaw warranty services and has a factory edge. Serial #0565.

Price is $175$150 shipped.

Cold Steel American Lawman
This is the old version with stainless liners. Edge was not properly ground(my fault) and so might look slightly uneven around the tip.

Price is SOLD shipped.
 
Last edited:
Spyderco Endura
Knife has been reground(FFG) by Tom Krein. Blade is semi mirror polished with a slight orange peel texture. Clip has been polished on one side only.

Note: Tip has been chipped off twice and reground. This blade is extremely thin and delicate! Don't buy unless you're aware of the care needed for such a thin and extremely hard knife!

Price is $75$60 shipped.

Kershaw Speedform
Serial #248. Blade was rubbed down with Brasso. Touched up on slotted paper wheels, but some of the factory grind lines are still visible.

Note: Handles have been slightly polished at a small spot near the blade due to contact with paper wheels when sharpening.

Price is $190 shipped.
 
Last edited:
hi, I'm Italian and I am interested endura KREIN Regrind.
I state the shipping costs for Italy
. Payment by paypal
Regards Antonio
 
You must log in or register to reply here.
Back
Top