6-16-15

[VCM3]

Good morning BF's members. Yesterday was a rainy day so it shut me down for pics,but today I'll attempt to list the 5 knives that came in,I mentioned them in my post yesterday.

First up,Eddie White Necker ....


Here is a "neck knife" by knife maker Eddie White. It has a blade of 1/8" thick stock 440C ss. Real nice grinding work,hollow ground & sharp. SS pins & tube,very nice handle work is contoured for your fingers up front. Feels great in hand. The blue G-10 has a very nice satin finish on it,not too polished,black liners. This would make a great EDC knife.OAL is 5-7/8" ,blade is 2.5" tip to handle with 2.5" of edge. Comes with a kydex neck sheath. Tang stamped E White on one side & 045 on the other side.Pre owned condition,never used,excellent
Includes shipping in the States
$125.

 

[VCM3]

Maker Ban Tang ,model BT4. 5/32" A2 steel,Rc 60. Not sure what type of grind but this knife is beyond wicked sharp. The Benchmade sheath it came in here with,is a decent fit but honestly for safety with this knife,I'd recommend sending it out to get a quality kydex system for it. OAL is 8-1/8" Blade is 4-1/8" from the tip to the handle ,with 4" of edge. Blue - black g-10, pins are hollow tubes with very nice flaring work. Razor sharp beast of a knife,really nice fit on it. Condition is pre owned, never used,excellent.
Includes shipping in the States & Paypal fee's too
$300.

 

[VCM3]

By Randy Lee


Small skinner by knife maker Randy Lee. OAL is 5-1/8" ,blade is 2-5/16" from the tip to the bolster,with 2-1/8" of cutting edge. 3/16" thick stock ATS-34 ss ,tapered tang. Nickel silver dovetailed bolsters are engraved. Buffalo horn scales,mosaic pins & brass tube. Right side vertical belt sheath,cowhide,fancy tooled,marked Sonja Lee,St. Johns AZ. Condition is pre owned,not used,very good .Includes shipping in the States
$old

 

[VCM3]

by Gunnar Momcilovic

Here is a very thin in hand,gent's utility by Norwegian knife maker Gunnar Momcilovic. It has real nice looking horn scales,probably water buffalo. Nickel bolsters. 3/32" 0-1 steel. O0AL 6-3/4" with a blade that measures (measured at the bottom,by the cutting edge) 3-1/4" from tip to bolster,with 3" of edge. Very nice leather sheath, set up for horizontal carry,left side,for a righty draw. Belt loop for a dress belt up to about 1-1/4" wide ,I estimate. Condition is pre owned,decent. Has handling marks on the blade & bolsters. Very slight pin checks on the scales,on some of the pins,not all,but seems tight. Includes shipping in the States
$250.

 

[VCM3]

this lot & probably for this thread,too.


Arial Salaverria Criollo

Criollo,aka gaucho knife by maker Ariel Salaverria . Steel is San Mai Damascus in 1010/1070 with 52100 core. OAL is 9-3/4" with 5-1/8" of edge. Blueish black micarta handle. Feels great in your hand. A magnificent knife to handle. Comes with 2 leather sheaths & faux leather storage sack. Condition is pre owned,never used,excellent. Includes shipping in the States
$old

 

[VCM3]

Randy Lee Sold


www.vcmcustomknives.com

Please contact me for your special price on anything listed FS on my site Thank You,-Vince