American Knives

[Rebl]

mid tech
is the biggest screw you to the knife community

 

[korn_2956]

its a riddle.

 

[blades&wrenches]

ok we all know it cost's money,but is bs
the only thing keeping good home grown blades off the market is $$
sure if you rich
no such thing as a buck 110 anymore
remember
if you feel your knife is worth it put it up as a buck,standard as we knew it
and ask is it worth it,,,,bet not,the basic mid tech's are junk

good steel and junk,if you can't sharpen a blade is useless.fck the holds an edge crap,when dull good luck

ok link is fail,like the piston,nice knife just built like crap

ok they close,smack the spine they will colse

so kinda like useless yes?

makes no sense,no matter the cost,any downward pressure on a lock,if the knife fails is bad,now is reasonable and can argue but the fact remains

there is only one that never fails,but you have no idea what it is.was done only once

fcking knife makers think they know,with the cnc and junk the put out

you are just a small factory,in 10 years is still junk

now what would change things,is take your "riches" and be honest
everyone knows the cost of material isn't that much in bulk
and training idiots to run machines is cheap
so stop and be less a rip off of your handmade and offer as it is

?huh?

 

[miltmaldo]

I think he is talking about Mick Strider .

 

[Rebl]

I'll use my fame and get cnc machines to make knives I never laid a hand on,but because my name is on it ,what a joke

 

[miltmaldo]

Ok maybe CRK .

 

[Rebl]

they should compete as any other company,jack up the cost's of stuff anyone can buy,is a shame

 

[korn_2956]

Hinderer?

 

[korn_2956]

can he see other people responding?

 

[Rebl]

crap you can get a cheap drill press,bench grinder and really overpriced steel for the price of a halfway decent knife

 

[blades&wrenches]

I'm guessing Brous...but who knows?

Nevermind..."in 10 years still junk" wouldn't apply to Jason Brous.

 

[Rebl]

If I'm going to spend 600$ you bet your azz it better be hand made and be worth it,no easy way outs anymore

 

[STAINLESS90]

makes no sense

I think you may have spouted a nugget of wisdom here.

 

[korn_2956]

Medford?

 

[Rebl]

The price of really poorly made "mid tech" junk has been out of control,you can get a china pos with cheaper materials but better tolerances than this junk

 

[Rebl]

ohh good steel and titanium,please is so cheap it isn't funny,next is well is my design,ok so,your trying to mass market,get it.be one thing or another

 

[Rebl]

same thing goes for ZT,what a joke,owned by KAI,and people think is a good product,well ok it is,but is just a product,no reason it should cost so much,same goes for Spyderco,which is a complete joke,bad all the way around

 

[Rebl]

Flat ground full height with a hole....the worst

 

[bladeboss]

The price of really poorly made "mid tech" junk has been out of control,you can get a china pos with cheaper materials but better tolerances than this junk

ohh good steel and titanium,please is so cheap it isn't funny,next is well is my design,ok so,your trying to mass market,get it.be one thing or another

Are you drunk, kid?

Sure, the materials are cheap.
Buy some good steel and titanium and let me know how well those raw materials cut.

Better yet, let's see the knives you've made since you're such an expert at it.
Because BUCK and CRK don't know how apparently.

 

[Rebl]

just stupid...lets take the most ugly design ever made and put a huge hole in it,go figure people buy it