B&T, short leuku, two spearpoints, and a pocket knife.

koyote

koyote

Feedback: +30 / =0 / -0
Joined
Mar 29, 2007
Messages
5,846
I'm going to dump this all in one thread to save space and be polite.

I'll pop each one as a separate post.

First up is a short bladed leuku. It's really close to my stead knife design, but without the full guard.

Overall, about 8 3/4 inches, the blade length is 4 1/2. Steel is 1084, forge finished and hand rubbed out, with a variable convex grind.

Scales are figured maple with blued steel pins. Really nice sweep for the drop on the blade guard.

Sheath is a ranger model, made by me.

Serial number of this one is 499

Asking $175, Sold

thanks!

499-02.jpg


499-03.jpg


499-04.jpg
 
Last edited:
Bird and trout knife, done in ash and 15n20


Overall, length is 7 inches, with a long slim blade of 3 3/4 inches length and just over 1/2 inch at the widest. Steel is 15N20, forge finished on the flats, with a nice high convex grind and a needle tip.

Scales are ash, with some figuring, and pin stock is bronze.

Sheath is a Koyote Girl made Ranger model. In the Ranger model pouch, the horizontal strap around the sheath holds the belt loop base, so no stitching goes through the sheath wall.

Serial number is 496

Asking $165, SOLD

thanks!

496-01.jpg


496-02.jpg


496-03.jpg
 
Last edited:
Koyote Pocket knife.

Haven't done one of these in a while, and this one is a bit different.

Overall length is 5 1/4 inches, with a blade length of 1 15/16 inches. (that should be legal EVERYWHERE!)

Steel is 15N20, with a scandivex grind and a sheepsfoot profile.

Handle wrap is linen cord. I make the cord out of linene thread by hand. Wrap is saturated in an acrylic.

Sheath is a Koyote Girl made deep pouch, with a freely moving pocket clip attached. As always, double needle, harness style, hand stitching an all sheaths, made by myself or her.

serial number is 495

Asking $95, $5 shipping. paypal, checks, money orders, .431 cast bullets, all good!

thanks for looking!


495-01.jpg



495-03.jpg



495-04.jpg
 
Spearpoint in gunkote.


I don't do a lot of cord wraps, but I've done a few recently. These next two are some of them.

This is a spearpoint design, a shortened version of my FKU(K) utility design. Overall length is 9 1/2 inches, with a blade length of 5 inches. Blade is 15N20, with a gunkote baked on finish. Scandivex grind. Light filework on thumbramp and rear blade guard area.

Handle is cord wrapped, with an underlayer of linen cord fully soaked in acrylic, the over wrap in black 220 cord. This one has a fairly broad handle and is very secure in a fist grip, but a bit big in my hands for saber grip.

Sheath is a very flat Ranger model, made by me.

serial; number is 502

Asking price is $165, $8 shipping. Paypal, checks, money orders, and elk salami all good.

thanks!


502-01.jpg


502-02.jpg


502-03.jpg


502-04.jpg
 
Last but not least, my favorite of the recent cord wrap projects.

This is another shorter FKUK design, blued, with an open handle wrap and just looks right.

Overall, 9 1/4 inches, with a blade length of 5 inches. 1084 steel, differentially tempered with a light forge finish left on, then the whole works cold blued. Thumbramp and guard area have some filework. Grind is scandivex- easy to keep up with a strop.

The handle is under wrapped with linen cord I hand lay from thread, soaked in acrylic. Over wrap is an open pattern, done with black 220 cord.

Sheath is an expedition model with a single broad horizontal strap. The belt hanger part is adjustable, reversible for LH carry, and removable for pack or strap mounting. As always, hand stitched, double needle. Sheath is made by me in this case.

Serial number is 501

Asking $180, SOLD
thanks!

501-01.jpg


501-02.jpg


501-03.jpg


501-04.jpg


501-05.jpg
 
Last edited:
update.

it's that time of year. If you ARE NOT a paid member, pay your basic and I take it off the price. If you ARE a paid member, take the price of a basic membership off.
 
You must log in or register to reply here.
Back
Top