Repost for these fine hand made bushcraft knives.
First is a lightly used Mark Wohlwend Large Bushcrafter,it is made of 1/8" L6.
The blade is 5 1/4" to the plunge line with forge finish on the flats with scandi grind.
The handle is 4 5/8" long with Brown Micarta & red liners.Brass & Aluminum pins.It is hand filling & very comfortable with nice rounded edges.
The sheath is made by me & comes with the EESE pouch & tin.No firesteel,but the loop takes a 5/16" rod.Holes spaced for Tek-Loks.
This knife came to me at work & I took it out back & tested it with some light chopping & feather stick making.
After chopping on a 4X4 I noticed rolls in the edge.Damn.
I Contacted Mark & sent it back & he re-heat treated it & changed the scales from Black to the Brown Micarta on it now as per my request.
Naturally I tested it when I got it back from Mark & it is good to go with no dings,rolls or chips after the re-heat treating.
$140.00 $130.00 shipped
Next is a standard Wohlwend Bushcrafter in 1/8" O1 & Cocobolo.
The scandi ground blade is 4" to the plunge & the handle is 4 5/8" long.
This is also used,but not abused.
I asked Mark about it & he said it is one of his early pre-California guardless Bushcrafters he made while living in Missouri.
The handle on this one is also very comfortable with no hot spots in use.
JRE(?) sheath included.
$135.00 $125.00 shipped. SOLD
Next is a full tang Wohlwend Puukko in 3/32" L6 or 1095,(not sure which) with forge finish on the flats & Olivewood scales with red liners.
The scandi ground blade is 2 15/16" to the plunge line & the handle is 4 1/8".
This is also used,but not abused.
Kydex sheath included.
$95.00 $90.00.00 shipped. SOLD
Next is a Wohlwend B&T.Mark called it a One Off Hunter/Skinner,but given it's size I like Bird & Trout better.
It is made of 1/8" L6 with Burlap Micarta scales & Red liners.
Full flat grind with forge finish on the flats.
The blade is 2 3/4" to the handle & the handle is 3 3/4".
I have only sharpened it with a ceramic stick,otherwise it is unused,but it do have some kydex scratches.
Kydex sheath included.
$75.00 $70.00 shipped.
Next are some Wohlwend Tin Knifes & a necker.
The top one is just a standard tin knife I blued using a blueing touchup pen.
The OAL is 3 3/4" with a 1 1/2" cutting edge.
The rear of the blade edge originally came back into the guard area & I ground it down so it wouldn't poke my finger.
L6 steel,1/8 thick.With leather sheath for pocket or keychain. $30.00 $25.00 shipped.
The middle one I put Tan Micarta scales on.The pins are Black Micarta.The blade is also blued.
The OAL is 3 3/4" with a 1 7/16" cutting edge.
I ground off a little more of the rear of the edge for safety's sake & put a shallow thumb ramp in the top spine after trying to do some thumb notches in it.
Orange Kydex sheath by me.It can be worn as a necker,on a keychain or it'll disappear in your pocket until needed. $40.00 $30.00 shipped
And the bottom one is a little one off Mark made for the fun of it out of 1/8"1095.
The OAL is 3 15/16" with a 1 11/16" cutting edge.
It has antler scales & comes with the alligator look leather neck/pocket sheath.
Full flat grind.That is RenWax on the blade in the pic,sorry about that. $50.00 $40.00 shipped.
Next is a JK Hiker in Bloodwood with black liners.
Used,not abused with sheath & fire steel.
It has the scratches & light patina to show how it's been loved & is still ready for more.
1/8" O1 steel.Convexed edge.Thumb jimping.
Blade is 4",handle is 4 1/4" with aluminum tubes.
$110.00 $100.00 shipped. SOLD
Next is a Daniel Combs(DanCo) drop point hunter in Walnut with kydex sheath.
The sheath has a swiveling belt loop so you can sit in comfort without it hangin' up.
3/32" thick 1084 steel,with forced patina by Daniel.
Blade is 4 3/4" & OAL is 9".
This is a very comfy in hand,slicing sun of a gun.
Only used to slice up an apple once.
COA included.
$75.00 $70.00 shipped. SPF
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
All knives will be shipped with RenWax on 'em.
Sorry,no trades,need the $$$.
You must be legally able to own/buy a knife.
The first firm "I'll take it" here or via PM or Email gets desired knife.
Shipping via USPS First Class with tracking except Priority for anything over $100.00.
Payment by Paypal(preferred) or USPS Money Order.
No international sale unless I know you & you pay the cost of shipping & accept the risks incase of loss.
Put the knife interested in & your forum name in any message sent please.
If you need more pics just ask & I'll email 'em to ya.
Email me at... myketheknife13 at gmail dot com
Thanks for looking.
Myke
First is a lightly used Mark Wohlwend Large Bushcrafter,it is made of 1/8" L6.
The blade is 5 1/4" to the plunge line with forge finish on the flats with scandi grind.
The handle is 4 5/8" long with Brown Micarta & red liners.Brass & Aluminum pins.It is hand filling & very comfortable with nice rounded edges.
The sheath is made by me & comes with the EESE pouch & tin.No firesteel,but the loop takes a 5/16" rod.Holes spaced for Tek-Loks.
This knife came to me at work & I took it out back & tested it with some light chopping & feather stick making.
After chopping on a 4X4 I noticed rolls in the edge.Damn.
I Contacted Mark & sent it back & he re-heat treated it & changed the scales from Black to the Brown Micarta on it now as per my request.
Naturally I tested it when I got it back from Mark & it is good to go with no dings,rolls or chips after the re-heat treating.
$140.00 $130.00 shipped
Next is a standard Wohlwend Bushcrafter in 1/8" O1 & Cocobolo.
The scandi ground blade is 4" to the plunge & the handle is 4 5/8" long.
This is also used,but not abused.
I asked Mark about it & he said it is one of his early pre-California guardless Bushcrafters he made while living in Missouri.
The handle on this one is also very comfortable with no hot spots in use.
JRE(?) sheath included.
$135.00 $125.00 shipped. SOLD
Next is a full tang Wohlwend Puukko in 3/32" L6 or 1095,(not sure which) with forge finish on the flats & Olivewood scales with red liners.
The scandi ground blade is 2 15/16" to the plunge line & the handle is 4 1/8".
This is also used,but not abused.
Kydex sheath included.
$95.00 $90.00.00 shipped. SOLD
Next is a Wohlwend B&T.Mark called it a One Off Hunter/Skinner,but given it's size I like Bird & Trout better.
It is made of 1/8" L6 with Burlap Micarta scales & Red liners.
Full flat grind with forge finish on the flats.
The blade is 2 3/4" to the handle & the handle is 3 3/4".
I have only sharpened it with a ceramic stick,otherwise it is unused,but it do have some kydex scratches.
Kydex sheath included.
$75.00 $70.00 shipped.
Next are some Wohlwend Tin Knifes & a necker.
The top one is just a standard tin knife I blued using a blueing touchup pen.
The OAL is 3 3/4" with a 1 1/2" cutting edge.
The rear of the blade edge originally came back into the guard area & I ground it down so it wouldn't poke my finger.
L6 steel,1/8 thick.With leather sheath for pocket or keychain. $30.00 $25.00 shipped.
The middle one I put Tan Micarta scales on.The pins are Black Micarta.The blade is also blued.
The OAL is 3 3/4" with a 1 7/16" cutting edge.
I ground off a little more of the rear of the edge for safety's sake & put a shallow thumb ramp in the top spine after trying to do some thumb notches in it.
Orange Kydex sheath by me.It can be worn as a necker,on a keychain or it'll disappear in your pocket until needed. $40.00 $30.00 shipped
And the bottom one is a little one off Mark made for the fun of it out of 1/8"1095.
The OAL is 3 15/16" with a 1 11/16" cutting edge.
It has antler scales & comes with the alligator look leather neck/pocket sheath.
Full flat grind.That is RenWax on the blade in the pic,sorry about that. $50.00 $40.00 shipped.
Next is a JK Hiker in Bloodwood with black liners.
Used,not abused with sheath & fire steel.
It has the scratches & light patina to show how it's been loved & is still ready for more.
1/8" O1 steel.Convexed edge.Thumb jimping.
Blade is 4",handle is 4 1/4" with aluminum tubes.
$110.00 $100.00 shipped. SOLD
Next is a Daniel Combs(DanCo) drop point hunter in Walnut with kydex sheath.
The sheath has a swiveling belt loop so you can sit in comfort without it hangin' up.
3/32" thick 1084 steel,with forced patina by Daniel.
Blade is 4 3/4" & OAL is 9".
This is a very comfy in hand,slicing sun of a gun.
Only used to slice up an apple once.
COA included.
$75.00 $70.00 shipped. SPF
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
All knives will be shipped with RenWax on 'em.
Sorry,no trades,need the $$$.
You must be legally able to own/buy a knife.
The first firm "I'll take it" here or via PM or Email gets desired knife.
Shipping via USPS First Class with tracking except Priority for anything over $100.00.
Payment by Paypal(preferred) or USPS Money Order.
No international sale unless I know you & you pay the cost of shipping & accept the risks incase of loss.
Put the knife interested in & your forum name in any message sent please.
If you need more pics just ask & I'll email 'em to ya.
Email me at... myketheknife13 at gmail dot com
Thanks for looking.
Myke
Last edited: