CPM 3V Sheepsfoot Utility /w Orange G10 and sheath - *SOLD*

Matt Markell

Matt Markell

Feedback: +9 / =0 / -0
Joined
May 12, 2012
Messages
846
Hi everyone, here is the last knife in a run of four of this design that I have made. I designed these knives to be small, lightweight, capable of precision cuts while remaining very tough and able to put up with lots of abuse. They are not a straight sheepsfoot, they have a bit of belly. I personally use one of the same design in my shop all of the time. These make a great working EDC knife.

Specs

Steel: 3/32" CPM 3V @ 60Rc Heat Treated by Peters
Grind: Right Hand Chisel FFG with screaming sharp edge
Handle: 1/8" Orange G10 with .060" black G10 liners
Hardware: Carbon Fiber pins
Finish: Scotchbrite belt finish
7" OAL, 3" cutting length, 1" tall
4.5oz /w sheath, knife only is 3oz

This one is SOLD shipped in the USA with tracking and insurance. I take Paypal, USPS MO and cashiers check. Email me or post "I'll take it" to buy. My email is markellmtthw@aol.com. Lifetime common sense warranty with free sharpening.

Boltaron(kydex) sheath included, small and large TekLok compatible (not included). The included paracord loops work as an ambidextrous horizontal/vertical belt loop system.


PICTURES!

FCfXbVn.jpg


F8c0nMt.jpg


jKbClH1.jpg


jXmAraw.jpg


mad2M19.jpg


Thanks for looking everyone and feel free to leave any questions or comments!
 
Last edited:
Sweet, I think this will be the best incarnation of the sheath! You have until Monday, then it's mine! hehehe
 
theHobbyist said:
Sweet, I think this will be the best incarnation of the sheath! You have until Monday, then it's mine! hehehe
Click to expand...

And the countdown is on! By the way, you are right, these have been getting better and better as I do them. This is the best of the batch imho.
 
Love the design. Just curious, would you do a model like this in a double ground flat grind? I prefer that over chisel. Again I love the design though!
 
Steel130 said:
Love the design. Just curious, would you do a model like this in a double ground flat grind? I prefer that over chisel. Again I love the design though!
Click to expand...

I wouldn't have a problem doing a V grind, the problem is that this is the last of this batch and I don't have plans to do another run in this steel for a while. I could do one in 1095 in a pretty reasonable amount of time. PM or email if that is something you would be interested in.

I have to say though, in my testing I have found that a chisel grind really works well with the modified sheepsfoot profile.
 
Steel130: If you want it, take it... I wasn't sure about the grind either. But let me tell you, these knives are some of the best performers I have.
I'll give it a bit more time =)
 
So for the record, this is number 3 :D, the other two have cut many MANY boxes, boned a few chickens. Sliced up a bunch of tripe. Butterflied several pounds of shrimp, and each have cut someone not expecting it to be as sharp as it was, sadly no stitches required!

PS Payment sent!!
 
theHobbyist said:
So for the record, this is number 3 :D, the other two have cut many MANY boxes, boned a few chickens. Sliced up a bunch of tripe. Butterflied several pounds of shrimp, and each have cut someone not expecting it to be as sharp as it was, sadly no stitches required!

PS Payment sent!!
Click to expand...

Haha, paypal received! I'll ship it out later today.

Thanks for your business!
 
You must log in or register to reply here.
Back
Top