Field Knife Magnacut and OD Green Micarta (SOLD)

CPE_Knives

CPE_Knives

Knifemaker / Craftsman / Service Provider
Feedback: +84 / =0 / -0
Joined
Oct 29, 2012
Messages
1,704
Good Afternoon,

This blade is made from 0.212" Magnacut ground to 400 grit and finished on an ultra fine scotch brite belt. Handle is OD Green micarta and brass

It comes with a kydex sheath which has a leather belt loop and attached firesteel. There is a tension screw with rubber washers at the top of the sheath so you can control the draw tension. Everything on the sheath is ambidextrous. The belt loop holes are also spaced for a teklok if you don't like the leather.

Price SOLD , shipping is included to continental United States via USPS. Preferred payment is via paypal.

Blade Steel: 0.212" Magnacut
Grind: Full Flat
Blade: 6 3/4"
Handle Material: Python micarta and brass
Overall Length: 11 1/2"
Sheath: Kydex with holes for a tek-lok
Weight: 8.92 ounces

If you would like additional pictures or have questions please contact me at cpeknives@gmail.com

20220810_183118.jpg20220810_183101.jpg20220810_183206.jpg20220810_183214.jpg20220810_183131.jpg20220810_183141.jpg20220810_183149.jpg20220810_183256.jpg

Comments are welcome thank you for looking,
Paul
 
Last edited:
That's a really slick rig you put together there. That shapely knife is the sort of knife I use as a goal. That sounds so much nicer than outright design theft. Kidding everyone. Paul already offered to send me plans for another knife I admired, joining some other top notch makers who take their time to advise and help me make better knives. This does remind me a little bit like a knife I made but about a zillion pay grades higher, deservedly so I hasten to add. Someone bought this beauty while I was writing this. No surprise there. Nice catch!
 
Grady slaughter said:
That's a really slick rig you put together there. That shapely knife is the sort of knife I use as a goal. That sounds so much nicer than outright design theft. Kidding everyone. Paul already offered to send me plans for another knife I admired, joining some other top notch makers who take their time to advise and help me make better knives. This does remind me a little bit like a knife I made but about a zillion pay grades higher, deservedly so I hasten to add. Someone bought this beauty while I was writing this. No surprise there. Nice catch!
Click to expand...
Thank you very much. I am always happy to help out. I have learned a lot here on blade forums and like to give back and contribute when I can.
 
Lately your work only stays available short amount of time, I believe it is because of the quality, price , materials used and genuine interest in the community. That being said I’m going to have to be a little faster if I’m going to be able to get in on your work.😢🤔😉
 
woodysone said:
Lately your work only stays available short amount of time, I believe it is because of the quality, price , materials used and genuine interest in the community. That being said I’m going to have to be a little faster if I’m going to be able to get in on your work.😢🤔😉
Click to expand...
Thank you. If you would like one just send me a message and I will get you on the list. Most of my work is made to order and doesn't make it here. I try to sneak one in for posting here as often as I can.
 
Very nice blade! Question for you, have you ever made anything else like this, with a little wider blade in a scandi grind with a wood handle?
Kudo's to you for making this knife out of Magnacut steel. Looking to buying one soon. Thanks!
 
You must log in or register to reply here.
Back
Top