first knife first time poster

P

pistolwhipped

Joined
Dec 31, 2013
Messages
6
Hello, I'm new here and I kinda wish I had found this place before I had started. I wouldn't have had so many guessing areas of this build. Anyways, I am just curious as to your thoughts about my first. I made my own furnace and it worked surprisingly well and I am super excited to start the next creation. My design was based off of a few of my favorite knives. I really like the Ken Onion "speed bump" so I did my best to incorporate that as well as the front hatchet style I like from certain survival knives. As you all know the first is a major learning experience and I had a lot of fun doing this. Thanks, Kevin

IMAG0935_zpse33fa4f4.jpg

IMAG0934_zps9a95defb.jpg

IMAG0925_zps2f9c3be5.jpg
 
Well, your handle work looks good, nice job on the pins. The blade attempts to be many things, but ends up confusing to the eye. Still, it's a good attempt for a first knife. I'd suggest you make another one, use a good knifemakers steel, such as 1084, and a simple straightward design. Concentrate on getting a good, consistent grind and a tight, well constructed handle, then sand it down and try for a good satin finish. Finally, either heat treat it yourself (read, ask lots of questions beforehand) or send it to a heat treating house. You will learn a ton of things, and want to do more knives, but beware, once the knivemaking bug bites there's no coming back. Good luck! And Welcome Aboard!
 
Without any detail, I can say you succeeded in making a knife shaped object at least. My suggestion for future builds is not trying to incorporate elements of different designs into one, but make one design that works well altogether. Lines need to flow from section to section, etc.

For more critique, we need:
Details? Type of steel, what do you mean furnace? Forge? In other words did you do the heat treatment yourself? Did you hand file, belt sander, etc?

And before Stacy beats me to it, fill out your profile so we can get to know you a little better.

Welcome to the forums and to knifemaking.
 
Thank you for all the good words and ancouragement. I used 01 tool steel, almost all hand tools like a file except the occasional help of a belt sander. I used coal and did the heat treatment myself. Turned out well for what I had but also learned a lot and found that the coal actually made markings on the blade while it was in my forge. I like the style that came of this knife. It was difficult at times but like I said it was a major learning process. The bug has bit.
 
yea I got the bug about a week ago. now im looking at spending 1000$ or so next week. have made 5 knives already. was going to make one today but some things came up hopefully ill get to tomorrow.
 
did ya see this yet ?



The Count's Standard Reply to New Knifemakers V31

The answer to a 13 year old student is different than a 60 year old machinist
We have members worldwide, you may have a local supplier, hammerin or helpful neighbour.
Please join our community and fill out your profile with location (Country, State, City), age, education, employment and hobbies so we get a sense of where and who you are.

Look at the threads stuck to the top of the page.

The basics in the simplest terms
Absolute Cheapskate Way to Start Making Knives-Printable PDF-Right Click and Save http://www.2shared.com/document/hk4wQruA/Absolute_Cheapskate_Way_to_Sta.html
http://www.scribd.com/doc/3622507/Jones-Scott-Jonesy-Absolute-Cheapskate-Way-to-Start-Making-Knives


Web Tutorials
Detailed instructions by Stacy E. Apelt http://www.bladeforums.com/forums/showthread.php?t=694673

The Things I Advise New Knife Makers Against-Printable PDF http://www.mediafire.com/?8og1ix21j9dcz4n

Handle Tutorial - Nick Wheeler-PDF http://www.mediafire.com/?02ra4do6xyzayeq
http://www4.gvsu.edu/triert/cache/articles/nw1/scales1.htm

Bob Egnath how to http://www.engnath.com/manframe.htm

Books
A list of books and videos http://www.bladeforums.com/forums/showpost.php?p=9435307&postcount=43

BladeForums - E-books or Google books http://www.bladeforums.com/forums/showthread.php?t=603203

Books I like:
David Boye-Step by Step Knifemaking
Tim McCreight-Custom Knifemaking: 10 Projects from a Master Craftsman
Clear, well organized, widely available and inexpensive.

Knife Design:
Think thin. Forget swords, saw-tooth spines, guthooks, crazy grinds and folders for your first knife.

Start with a drawing and show us, we love to comment on photos.
Then make a cardboard cutout template & draw in handles, pins and such.
Use playdough to shape a comfortable handle, good handles are not flat.

How to post a photo
http://www.bladeforums.com/forums/s...AL-Displaying-your-photographs-on-BladeForums

Google books thread for Lloyd Harding drawings, Loveless book & Bob Engnath Patterns. http://www.bladeforums.com/forums/showthread.php?t=603203

Bob Engnath Patterns in a PDF http://www.mediafire.com/?qgx7yebn77n77qx


Forging Books:
Lorelei Sims-The Backyard Blacksmith - A modern book with colour photos - forging - no knifemaking.

Jim Hrisoulas- Check for the cheaper paperback editions.
The Complete Bladesmith: Forging Your Way to Perfection
The Pattern-Welded Blade: Artistry in Iron
The Master Bladesmith: Advanced Studies in Steel

Machine Shop Basics -Books:
Elementary Machine Shop Practice-Printable PDF Http://www.archive.org/download/elementarymachin00palmrich/elementarymachin00palmrich.pdf

The Complete Practical Machinist-Printable -1885-PDF http://ia700309.us.archive.org/6/items/completepractic00rosegoog/completepractic00rosegoog.pdf
Right Click and save link as.
It’s being reprinted now if you prefer paper books

The $50 knife Shop-not reccomended
This book has a great title, but is NOT gospel. It confused me for a long time.
Forging is NOT necessary; you can file and grind to create a knife (stock removal)

Forget the Goop Quench BS, Even back when they used whale oil, it was still liquid oil.
Use a commercial quench oil & match oil speed to the steel type;
Grocery store canola oil works for some steels like 1084.

Junkyard steel requires skill and experience to identify and heat treat it properly.
Forget Lawnmower blades and railroad spike, start with a new known steel.
Good heat treating needs accurate temperature control and full quench.
You can buy proper steel like 1084FG from Aldo very cheaply, and quench in Canola.

Cable damascus is an advanced project has no place in a beginner’s book.

The grinders are the best thing about this book, but 2x72” belt grinders free plans are now on the web.


Videos

Don't be this guy
http://www.youtube.com/watch?v=gEOTtslHARQ

Heat Treating Basics Video-downloadable
Right click and save this. Watch it once a day for 10 days. http://www.archive.org/download/gov.ntis.ava08799vnb1/ava08799vnb1_512kb.mp4

Safety-video
Right click and save this. Watch it once a day for 10 days. http://www.howtomakeaknife.net/FreeStuff/SafetyVideo.wmv

Many knifemaking videos are available, some better than others.

The best beginner videos I have seen:
“Steve Johnson-Making a Sub-Hilt Fighter”

"Ed Caffrey - Basic Bladesmithing-Full DVD-ISO"

“Custom Knife Sheaths -Chuck Burrows - Wild Rose”
-(Paul Long has 2 videos, his sheath work & videos are fantastic, but more advanced-with inlays, machine stitching)

Green Pete's Free Video
Making a Mora bushcraft knife, stock removal, hand tools, neo tribal / unplugged heat treat.
Use a piece of known steel, not a file. This as an example of doing it by hand with few tools.
"Green Pete" posted it free using torrent files.
Be sure to look at the other titles I mentioned too - spend some time searching.

Greenpete Knifemaking Basics-on TPB
http://thepiratebay.org/torrent/499...femaking_Basics_-_Make_a_Mora_Bushcraft_Knife

How to download that video
http://www.utorrent.com/help/guides/beginners-guide

See a list of videos for rent and read the reviews, Some are good, some bad, expect to wait weeks or months

http://smartflix.com/store/category/9/Knifemaking

Draw Filing Demonstration
YouTube video -Draw Filing-for a flat finish http://www.youtube.com/watch?v=Dec78RQsokw

Steel
The “welding steel” at Home Depot / Lowes… is useless for knives.
Forget about lawnmower blades ,files and other unknown junkyard steels.
For all the work involved, it is very cheap to buy and use a known good steel.

If you send out for heat treating, you can use
Oil quenched O1, 1095, 1084
Or air quenched A2, CM154, ATS34, CPM154, 440C, plus many others.

For heat treating yourself with minimal equipment, find some Eutectoid steel and quench in Canola oil.
1084FG sold by Aldo Bruno is formulated for Knifemaking, Cheapest & made for DIY heat-treat.
http://njsteelbaron.com/
Phone # 862-203-8160

Suppliers List
http://www.bladeforums.com/forums/showthread.php?t=699736

Heat Treating
http://www.bladeforums.com/forums/showpost.php?p=9143684&postcount=7

You can send blades out for heat treating at $10 or $15 per blade for perfect results, and avoid buying the equipment.

Air Hardening Stainless Steel Only
Buck Pau Bos -Be sure to check the Shipping and Price tabs.
http://www.buckknives.com/index.cfm?event=bio.paulBos#
http://www.texasknife.com/vcom/privacy.php#services

Oil Hardening Carbon Steels and Air Hardening Stainless Steel
http://www.petersheattreat.com/cutlery.html
http://www.knifemaker.ca/ (Canadian)

FAQ's
http://www.hypefreeblades.com/faq.html

1095 is a good carbon steel, but a bad choice for a beginner with limited equipment.
1095 is "Hypereutectioid" and needs very precise temperature control and proper fast quench oil Like Parks 50 or Houghton K
Kevin Cashen - 1095 - hypereutectoid steel http://www.bladeforums.com/forums/showthread.php/673173-Working-the-three-steel-types

If you are sending one or 2 knives out for heat treatment, use 154-CM or CPM-154 or CPM-s35vn and ship it out to TKS -Texas Knifemaker Supply
It's the cheapest way to do 1 or 2 because of HT minimum charges.



Quenchants for Oil hardening steel
Forget the Goop Quench and Motor oil.

Use commercial quench oil & match oil speed to the steel type;
The best explanation and classification oil speeds I've seen
http://knifedogs.com/showthread.php?28197-Hardening-II-Quenching

Grocery store canola oil works well enough for your first knife-if you use the right steel like 1084

Brine and water are cheap, and technically correct for "water hardening" steels W1 and 1095 but a fast oil like Parks 50 or Houghton Houghto Quench K are less likely to give you broken blades
If you use water or brine, expect to hear a "tink" and have a cracked or broken blade

Glue – Epoxy
Use a new package of slow setting 30 min to 1 hour, high strength epoxy to attach blades to handles and seal out moisture.
Slow epoxy is stronger and gives you time to work with it.
Surface Prep is vital, drill tang holes/ grind a hollow, roughen the surfaces with abrasive or blasting is best.
Ensure the surface is clean and no oil including fingerprints.
Use Acetone & Alcohol, or Blasting.
Don't over clamp it. Avoid a “glue starved joint” when all the adhesive is squeezed out.
Use:
Brownell's Acraglas
West Systems G Flex
JB Weld


Grinder / Tools

Hand Tools
You can do it all by hand with files and abrasive cloth like the Green Pete video.
Just use 1084 instead of a file.

Stacy - 10 Tools
http://www.bladeforums.com/forums/showthread.php/1049666-Ten-Tools?p=11983527#post11983527

Photo of a nice bevel filing jig
http://www.flemingknives.com/imagesPrime/FileStation/KPicB007.jpg
Http://farm9.staticflickr.com/8486/8152684286_312b9fc8da_b.jpg
http://www.youtube.com/watch?v=r9iNDRwwBQQ#t=330

Grinders
A professional three or four wheel 2x72 is worth it
In my opinion, variable speed and a small wheel attachment are essential on a good grinder.
You can almost always improve tracking with more belt tension. It needs to be way tighter than you first think.

Entry Level Grinders
Sears Craftsman 2x42 belt grinder http://www.sears.com/shc/s/p_10153_12605_00921513000P?prdNo=3

Low Speed Modification Craftsman 2x42 belt grinder http://www.youtube.com/watch?v=2qfYT_m2Tw0


Commercial Production 2 x 72” Belt Grinder Reviews
http://www.prometheanknives.com/shop-techniques-3/grinders
http://www.cnccookbook.com/CCKnifeMakingGrinders.htm


DIY 2 x 72” Belt Grinders

KMG Clone Free Plans
http://www.metalwebnews.com/manuals/knife-grinder.pdf

NWG No Weld Grinder
http://usaknifemaker.com/plans-for-the-no-weld-grinder-sander-nearly-50-pages.html

EERF Grinder (EERF =“Free” backwards)
http://www.wilmontgrinders.com/Pages/EERFGrinder.aspx
http://blindhogg.com/blueprints.html

Buy the kit
http://polarbearforge.com/grinder_kit.html

What Belts to buy?
http://www.usaknifemaker.com/abrasive-belt-basics-what-kind-should-i-buy-p-1393.html



VFD Variable Speed made simple

Step pulleys are not as cheap as you may think
Maska cast steel pulleys are good and well balanced $75 EACH here plus shaft, bearings, belt

It all adds up to about 1/2 the price of a KBAC-27D

I like direct drive with no belts using a VFD and 3 phase motor for about $200 over the price of the step pulleys with much finer control.

Yes you can get cheaper NEMA 1 VFD’s and build your own enclosure
You may find them cheaper at other retailers and on Ebay direct from china.

Wayne Coe
http://www.waynecoeartistblacksmith.com/Motors___VFDs.html

VFD-
KBAC-27D

Motor
3 phase 220v 1.5 HP motor, TEFC, frame 56 or 56C,
RPM is up to you many are happy with a 1700 RPM running at double speed.
Make sure it has a footed base for the KMG and NWG, or a C flange face mount for Bader, Bee, Wilton and GIB styles.
I get them on ebay, even with paying $80 for shipping to Canada I save $$$ on a used motor.

The 1.5 HP combination is the most common, as reported by Rob Frink
It allows you to plug into any 110vac, 15 amp outlet.
A 2 HP motor requires a 220vac input.

There are cheaper VFD units like the TECO, but the only VFD I have found that will run a 1.5 HP motor on a 110v 15 amp input is the KBAC27D

It is NEMA4, sealed from metal dust that can burnout the unit.
It has good community and company support, manuals, hook-up diagrams, photos and settings on Rob Frink’s website.

I like the fact that I can buy it from a local distributor in Canada.

Travis W reports running a 2 HP on a 110v circuit, but I haven’t tried it.

Hookup is dead simple
http://www.beaumontmetalworks.com/VS-setup.html


Safety Equipment
Protect your -Eyes, Ears, Fingers, and Lungs – remove jewellery and use safety gear.

Respirators
Chronic lung disease and cancer really suck the joy out of life.
Goggle "Ed Caffrey lung cancer"
Wearing a mask on the top of your head doesn't count.

The minimum I would consider are silicone half masks with a P100 Filter
3M 7500
http://multimedia.3m.com/mws/mediaw...Ox_Uev7qe17zHvTSevTSeSSSSSS--&fn=CH7500FP.pdf

and North 7700
http://www.amazon.com/North-Safety-770030L-Silicone-Respirator/dp/B002C08YCW
http://www.amazon.com/North-7580P100-P100-Particulate-Cartridge/dp/B000UH6PSE/ref=pd_bxgy_hi_img_b.

Use a VOC & P100 combo cartridge for protection against acetone and solvents.
Prefilters can snap over the main filter for longer life.
There are 3 sizes, buy one in person at a safety supplier and get it fitted.

For beards, pick one of these
3M PAPR
Resp-O-Rator
3m Breathe Easy
Trend Airshield Pro
Air Cap II


Searching

This Google page searches BF and works well.
http://www.google.com/cse/home?cx=011197018607028182644:qfobr3dlcra

Can I get rich making knives ?
http://www.bladeforums.com/forums/s...knife-making-worth-it?p=11980504#post11980504

V31 Nov 1, 2013
Darrin Sander is no longer HT blades.
http://www.bladeforums.com/forums/showthread.php/1074496-I-m-no-longer-heat-treating-blades
 
Thank you for the details. Welcome to the brotherhood of the calloused fingers.

And the count's standard post should be a required syllabus for knifemaking 101. Lots of good info there.
 
Welcome to Bladeforums and Shop talk.

All in all, it is not the worst first knife I ever saw.


The blade is too many different shapes. It would have been far better as a simpler drop point hunter or a skinner.

The handle is pretty well done. It should have a bit more curve along the front part at the ricasso. Kudos on rounding the edges and sides.

With all due respect to Ken Onion, the speed bump is atrocious.
The other bad feature is the recurved blade edge. It would look and cut much better as a plain curved edge.

The pins are not centered , and are too small.
 
Thank you for the critique. I agree on the pins. What size would you recommend? Is there a rule of thumb for pin size?
 
bladsmth said:
...With all due respect to Ken Onion, the speed bump is atrocious...
Click to expand...

I love Kershaws, and own a couple Onion designs... The speed bump, however, would even get regifted. Always looked like the blade that didn't know what it wanted to be when it grew up...
 
Pins need to have enough surface to hold the scales a bit. 1/8" is the minimum, but 1/4" will have much better grip. Corby bolts ( and Loveless bolts) are even better, as they physically bolt the scales down permanently.
 
Start with a new piece of metal like 1084 and just keep this one as your first learning experience and improve on it how you see fit. And the advice you get from these guys here (not me) are guys who have tons of experience, listening to them would only benefit you
 
Thanks. I've already started my second. I agree I can see these guys know their stuff so I'm thankful for all the critiques.
 
I think it turned out well for your first knife. The thumb stop matches up well with the curve of the edge following the tip and ends up being functional for a skinner. However, the belly of a skinner should drop lower to allow more continuity along the edge. I'm not sure a skinner was your goal but functionally, to the greatest extent, I think that is what you ended up with. I am a proponent of 'form follows function'. Using too many design parameters results in a product that is marginal for many of the parameters. So, IMO you will end up with a better design if you narrow your focus.
 
The handles seem to be nicely contoured going by the second pic. I believe the trailing point simply needs to be toned down a bit and a recurved edge isn't necessarily for this type of knife. The pin size would have been ok-but you should've used more of them, probably around 4 or 5.
 
You must log in or register to reply here.
Back
Top