Lets see some Hinderer action

Barman1 said:
Can someone tell me the size of Hinderer clip screws or where I can grab a set?
Just plain non-anodized.
Or if someone has a couple laying around?
I've got a pair of copper screws for trade & can throw in a set of pb washers if someone wants to ship me a set....
Click to expand...

One non BF Member dealer is supposed to be the sole source (according to Hinderer) of screws and teflon washers but I have never seen any in stock. I don't have any extras, but maybe Whitty can take car of you when he gets back from vacation.
 
JB in SC said:
One non BF Member dealer is supposed to be the sole source (according to Hinderer) of screws and teflon washers but I have never seen any in stock. I don't have any extras, but maybe Whitty can take car of you when he gets back from vacation.
Click to expand...
Thanks.
I found a set of blue anodized screws on ebay from one of our trusted dealers so I grabbed them this morning.
Should work with the other blue hardware I installed.

On another note I polished and installed PB washers and must say there's no big difference in opening.
The most noticeable difference is that it feels more solid and when I set the knife down on its side I don't get that "rattle" I got from the teflon flex allowing the blade to contact the liner. (I'm guessing that's where that rattle was coming from?)
 
A little Red, White, and Blue All-American Hinderer Action for today. Happy 4th, Everyone!

k7FEkRx.jpg
 
Barman1 said:
Thanks.
I found a set of blue anodized screws on ebay from one of our trusted dealers so I grabbed them this morning.
Should work with the other blue hardware I installed.

On another note I polished and installed PB washers and must say there's no big difference in opening.
The most noticeable difference is that it feels more solid and when I set the knife down on its side I don't get that "rattle" I got from the teflon flex allowing the blade to contact the liner. (I'm guessing that's where that rattle was coming from?)
Click to expand...

Sorry, I thought you were looking for screws (the phillips head) for the clip/filler tabs, not handle screws/nuts. Plenty of vendors have the handle screw/nuts, only one is the exclusive vendor for the phillips head and teflon washers.
 
JB in SC said:
Sorry, I thought you were looking for screws (the phillips head) for the clip/filler tabs, not handle screws/nuts. Plenty of vendors have the handle screw/nuts, only one is the exclusive vendor for the phillips head and teflon washers.
Click to expand...
I am looking for the clip/filler phillips with no anodizing but I found a set of 4 that are anodized blue so I grabbed them.
They will match all of the other blue anodized hardware hopefully.
 
Barman1 said:
I am looking for the clip/filler phillips with no anodizing but I found a set of 4 that are anodized blue so I grabbed them.
They will match all of the other blue anodized hardware hopefully.
Click to expand...

They are usually steel, I've never seen Hinderer made Ti phillips head screws.
 
Broke down and cleaned up my Half Track and Jurassic tonight after being exposed to sand and salt water last week while on vacation. Both knives break down and go back together dead centered with ease. Entire time spent for both knives combined was about 20 minutes. Probably the 2 easiest knives to disassemble and reassemble that I own!

https://flic.kr/p/Vi2hxe https://www.flickr.com/photos/57703464@N02/

https://flic.kr/p/Vi2ht6https://www.flickr.com/photos/57703464@N02/

https://flic.kr/p/WgD1Ss https://www.flickr.com/photos/57703464@N02/
 
I'd love to see a 3" version of the Maximus with a single sharpened edge (I'm too clumsy to handle a double edge).
 
You must log in or register to reply here.
Back
Top