Lowrider clips for Kershaws

Sorry for bringing an older thread to the top, but do you have any pics of a leek with a low rider clip tip up? I love this little knife but tip up sticks out way too much! Don't care about the lanyard hole or the lock if that matters. Just low and tip up!
 
That looks just about perfect. After reading another one of your posts concerning the leek, I'm guessing theres no way to get it any lower? Either way I want one!
 
Got it, or at least I assume that is you. Its unlikely I had two back to back inquiries for the same model. The clip is packed up to ship out tomorrow morning. Thanks for your interest.

STR
 
Someone must've seen this thread cause I haven't ordered one yet! The next one will probably be me though. :D

edit: order email and paypal payment sent.
 
Last edited:
Okay so I did get two of the same clip. Alright my bad. The one packed up is for someone else. I'll have to make one for yours in the morning and thats not a problem. I'll have it ready to ship out by the time my mail arrives. $34 total and I did just now get your work order. It will be out to you tomorrow. STR@bladeforums.com is my pay pal. Thanks
STR
 
I'm in no hurry. But you should have a paypal payment. I'll post pictures of it installed and in the pocket when it arrives.
Thanks!
 
I do see it. I'll have one out and on the way as planned in the morn. Thanks

STR
 
STR,
I need one of your fine low rider clips in Black,for my Kershaw Shallot 1840CKT,please.
Tip-up carry; no lanyard.
Can mail it to you,if you like.
Sending PayPal next.
Thanx!
~Gnarly
P.S. Really like my prybar!
 
Gnarly said:
STR,
I need one of your fine low rider clips in Black,for my Kershaw Shallot 1840CKT,please.
Tip-up carry; no lanyard.
Can mail it to you,if you like.
Sending PayPal next.
Thanx!
~Gnarly
P.S. Really like my prybar!
Click to expand...

Cannot get black colors sorry. I have one done (bead blasted) that should mount right up to that folder just fine but it may require some simple adjustment on your part once it arrives. I can walk you through that as its quite simple to do. If you prefer to mail me the knife all anyone needs to know to do that is here. Thanks. http://www.bladeforums.com/forums/showthread.php?t=525771

STR
 
No problem,STR; send it!

I have a collection of stuff to send Jeff @ 4Bushweaponsrefinishingsystems for Ceracoating...I'll ask Jeff to do it in a flat black,to match the Shallot.

I'll be glad to get it,STR.
The only complaint about this daily user is the factory clip causing it to ride ~3/4" above my pocket and hanging up on things.

Thanx! for your rapid reply,

~Gnarly
 
Hi STR,
Great work! I am looking for a deep clip for my tiny OD-2 (I know,the clip will cost more than the knife!) as I love it that much. Always in my pocket, but would appreciate a totally submerged carry. Have you done one of these before? Cheers.

Here is an image of the knife:

KS17701.jpg
 
No but I can tell from looking at it that it has a hole pattern in the clip that is just too close to allow a folded over stem to weave between them. The clip stem that is folded over for the 180 to make the clip would have to be so thin for width just to be able to access the screws with a driver let alone install them that it would be far too weak to even hold up in use. I doubt it would have sufficient spring tension to really do much for grip to the pocket either. Using the existing holes to make a low rider on that one is out of the question based on what I'm seeing. Sorry

STR
 
You must log in or register to reply here.
Back
Top