Up for sale are a few knives that are not getting much use in my collection. All knives come with original packaging, except the Hinderer which does not have the original box. Pricing is PayPal G&S and shipped Priority Mail (CONUS only). More detailed pictures available upon request.
1. Spyderco Ikuchi - This knife has seen very light use but shows no signs of wear and still has a sharp factory edge. Price $110.00 SOLD.
2. Benchmade 940-1501 - This knife has been sharped to 20 DPS on a Wicked Edge and the pocket clip has some wear. Otherwise no visible marks. Blade is centered. Price is $150.00 SOLD.
3. Hinderer XM-18 3.5" DLC M390 - This is a no-choil spanto exlusive from DLT Trading and comes with a texture copper scale installed. This knife has not been used, but the copper has some patina and I did grind the sharp point off of the flipper tab with a Dremel, so the DLC is worn in that small area (can provide pics). Also comes with additional bronze and teflon washers and original battleship grey scale and titanium liner. Price is $450.00 SOLD.
4. Hoback Kwaiback Bronze Anodized - I purchased this knife used and have not carried it, but I did sharpen it to 23 DPS on my Wicked Edge. Price is $350.00
5. Microtech Custom Sigil - This is a custom run Microtech Sigil (the 3.5" smaller model) with an apocalyptic finish Elmax blade and apocalyptic finish titanium scales. Just recently back from a sharpening by Microtech. Has all packaging and laser cut COA. Price is $450.00
6. ZT 0452TIBLU - I purchased this knife new and have used it and carried it frequently. The scales show snail trails and signs of wear, as well as a ding on either side of the top of the scales from when it was dropped (can provide additional pics). The blade has been sharpened to 20 DPS on my Wicked Edge. Blade shows some light marks toward the tip. Price is $150.00
7. Microtech Socom Elite Manual - This knife is LNIB. I purchased it new but it had some lock rock and had to be sent to Microtech to be repaired under warranty. They replaced the lock bar, but there is some light marking on the pivot screws from their disassembly (go figure). Price is $200.00 SOLD.
If you have any questions please feel free to send me a PM or email me at dan r 70 @ gmail.com
1. Spyderco Ikuchi - This knife has seen very light use but shows no signs of wear and still has a sharp factory edge. Price $110.00 SOLD.
2. Benchmade 940-1501 - This knife has been sharped to 20 DPS on a Wicked Edge and the pocket clip has some wear. Otherwise no visible marks. Blade is centered. Price is $150.00 SOLD.
3. Hinderer XM-18 3.5" DLC M390 - This is a no-choil spanto exlusive from DLT Trading and comes with a texture copper scale installed. This knife has not been used, but the copper has some patina and I did grind the sharp point off of the flipper tab with a Dremel, so the DLC is worn in that small area (can provide pics). Also comes with additional bronze and teflon washers and original battleship grey scale and titanium liner. Price is $450.00 SOLD.
4. Hoback Kwaiback Bronze Anodized - I purchased this knife used and have not carried it, but I did sharpen it to 23 DPS on my Wicked Edge. Price is $350.00
5. Microtech Custom Sigil - This is a custom run Microtech Sigil (the 3.5" smaller model) with an apocalyptic finish Elmax blade and apocalyptic finish titanium scales. Just recently back from a sharpening by Microtech. Has all packaging and laser cut COA. Price is $450.00
6. ZT 0452TIBLU - I purchased this knife new and have used it and carried it frequently. The scales show snail trails and signs of wear, as well as a ding on either side of the top of the scales from when it was dropped (can provide additional pics). The blade has been sharpened to 20 DPS on my Wicked Edge. Blade shows some light marks toward the tip. Price is $150.00
7. Microtech Socom Elite Manual - This knife is LNIB. I purchased it new but it had some lock rock and had to be sent to Microtech to be repaired under warranty. They replaced the lock bar, but there is some light marking on the pivot screws from their disassembly (go figure). Price is $200.00 SOLD.
If you have any questions please feel free to send me a PM or email me at dan r 70 @ gmail.com
Last edited:
