My workshop & stamp on knives

Status
Not open for further replies.
MB - your story about making identical copy of popular selling tracker knife is believable because I've seen me-clone for variety of products for quite a few decades now, especially in Asia. One can buy a cheap Damascus billet and produce what you claimed had produced. People on BF are protecting the integrity of this forum and also protecting potential buyers by exposing bad sellers/products. So far, there are signs of dishonesty on your part, if you are honest in this trade, you'll be vindicated.

Is the left hand in pic & video, yours? I am asking because the blood veins on the back of the hand seem a bit mis-match.
mb.png
 
Not the zoom... it's the vein go across the back on the middle finger vs going straight to the middle knuckle. I did looked at my hand prior my post above - I do have a few veins go right across the back of the hand before flow toward the knuckles. The flow doesn't change much with open or close fist.

Maybe I am too skeptical, nevertheless thanks for clarified the left hand in pic & video is yours.

Mughal-Bros said:
It cud b bcz zoom and without zoom sir . and i am sorry for dishonesty .
Click to expand...
 
it's 7:31 am here and i didn't sleep all the night just to talk to you guys . now i am getting 2 hours sleep then wake up and start work on the knife so i will make more pics and post here .
 
Mughal-Bros said:
in my fucking video i am tampering my knives .
Click to expand...

Can you be more specific please ?

In English "tampering" does mean what was previously mentioned,

To interfere in a harmful manner




I assume that it is part of the heat treatment process, can you describe the process and equipment you use ?
which action are you performing in the video ?
 
A little light reading for those who care to take a look, It seems R&R and WB are smack in the middle of one of the largest cutlery manufacturing sites in the world, and likely live less than 10 miles apart, Wazirabad and Gujranwala

http://trtapakistan.org/sector-products/industrial-products/cutlery/

http://www.smeda.org/index.php?opti...project-cutlery-institute&catid=34&Itemid=555

http://tribune.com.pk/story/37355/exploiting-the-potential-of-cutlery-exports/

These paragraphs jumped out at me, looks like the pakistanis have a plan LOL

Exports make up only a small fraction of world trade in cutlery, swords and hunting equipment, which amounts to over $11 billion. This is one sector where Pakistan has developed capabilities to penetrate high value / high income markets such as Germany, USA, France, Belgium etc.

The main raw material used in the production is ‘steel’. Around 80% of this steel is manufactured locally and the remaining 20% is imported from Germany and Japan. A recent innovation in the cluster is the development of Damascus steel – which is used for the manufacturing of hunting knives.
 
Last edited:
Can we see a picture of your hardness tester with a piece of paper that has bladeforums written on it next to it?
 
Sam Wilson said:
If you're unfamiliar with R&R Cutlery, I would contact them, because it looks like you guys are making the same tracker knife. I could be wrong, though.

This pic is from your webstore, your "first tracker knife":

viewThumb.jsp


And here is a strikingly similar "tracker knife" from R&R Cutlery, on his Facebook page:

10325736_624776000950127_8401945337254554398_n.jpg


Just a thought.

Sam
Click to expand...
I'm not qualified to comment on who is who and who made what, I'm just here to point out that knife looks kind of ugly and really nonfunctional.
 
It's a shame this guy is allowed to sell his mass-produced wares under the guise of being a custom knifemaker. At least this thread has been entertaining.
 
how in the hell you can say my products are not good ? did u get one from me yet in your hands ? you guys are really amazing .
 
OK, folks.
Lets all just move along and let this go.
Mughal needs to get some sleep and we all have better things to do. There isn't anything else to be said, so I am closing this thread.

If you want one of his knives, buy it from him on his Exchange thread......if not, hit the back button and move on to real knifemaking threads.
 
Status
Not open for further replies.
Back
Top