Several custom knives available!

[Taz]

I have several blades I made over the last year (Some are a bit older!) that I want to move! These are all made by me in Connecticut, all sales CONUS only! PM for paypal or Venmo info! I can get more pics of these as well.

First up is a 3.25” Cruwear blade, 8” OAL, 60 HRC (BOS heat treating), full tang, red G10 liners, black pins and Orange Denim/Burlap handle scales, Blaze Orange Carbon Fiber Holstex sheath. $250 conus only


2.75" S90V Warncliff in 3/32" steel, full flat grind. I believe BOS did the heat treating on these to 61? Super thin, pointy and slicey! 7 3/8” OAL. Frame Handle is Red G10 guard and liners, ivory paper micarta frame and stabilized Buckeye Burl handle scales. $225 CONUS



CPM 3V blade, 3 1/8" cutting edge, .156” at the spine, 60 HRC (BOS Low Temper), with Day Glo AmeraGrip handles, mosaic pins and toxic green kryptek sheath. 8” OAL, $250. The handle material glows in UV light as well!


2.75" S90V blade (BOS to 61 HRC), .078" at the spine and tapers to the point. Super thin and slicey!! Handle is natural canvas micarta guard and liners, ivory paper micarta frame and white with 2 black stripe paper micarta. 7 3/16” OAL, Kryptek Kydex sheath, $225


2.75" Elmax blade, 62 HRC (Jarod Todd I believe?), 3/32" stock, 600 grit hand rub finish, hidden tang into a black g10 frame handle with toxic green liners and the scales are stabilized and dyed teal burl handles. 7 3/8” OAL. Blade is super slicey and light! Kydex belt sheath is included. $200




4” Clip Point Damascus blade, 9 3/8” OAL. 125CR1/15N20, 144 layers. Kevlar guard with G10 spacer, Orange AmeraGrip handles. I made the Damascus myself and did the heat treat in my heat treat oven, 61-62 HRC. $350.

3” cutting edge reverse tanto blade, 8” OAL, 3/32” thick Nitro V at 62 HRC (BOS Heat Treat), OD Green Ameragrip handles, $200 SOLD


3 3/16” edge, 8 1/18” OAL, 62 HRC (BOS heat treat), 1/8” thick, Nitro V, blue denim Micarta handles, mosaic pins and stainless lanyard tube. There are some kydex scuffs on the blade, so I am lowering the price down to $175! I have a few more of these blanks in Nitro V that I can build up as well! This is one of my standard models, so I try to keep a few hardened blanks on hand ready to customize and grind out!


3 1/8” 62 HRC Nitro V blade (BOS heat treat), 1/8” thick, Vintage Tri Color Canvas Micarta handles, 8” OAL. $200 (Again from one of the above blanks) TRADED


And last but not least!

3 3/16”, 64 HRC Magnacut blade, 8 3/16” OAL, with natural canvas micarta, toxic green pins and liners, $250. I did the heat treat/cryo myself on this one!


Thanks for looking!

 

[BluegrassBrian]

Wow- all look fantastic!

 

[Taz]

Thank you! Been working at making my work cleaner, getting some standard models/designs down, and getting the shop equipped more fully! I like doing 2.5-4" EDC/Hunting type blades, but I do some kitchen stuff occasionally and want to do more larger choppers as well now that I have the larger oven!

 

[Scott Hanson]

You sure have been keeping busy, keep up the good work!

 

[jfk1110]

Some fine work up there...............Those last three blades are great....... Lines, materials, execution = perfect

 

[MicronKnives]

Wow, those are all gorgeous

Dming for that reverse tanto!

 

[Taz]

Dm sent MicronKnives! Reverse Tanto is pending for you!

 

[Taz]

Reverse Tanto is sold!

The last 3 are some of my newest work. The Blue Denim Handle one and the Tri Color one are from the same blanks I had NJSB water jet cut for me, just different blade shapes ground. Blue one has more belly up front and is wider, or I can narrow it down and make it pointier like the vintage tri color one. The last 3 are pretty close size wise, with the Magnacut one having a slightly longer handle and a different shaped handle (finger choil/long rear curve) vs the finger/pinky well and palm swell of the other ones; that one was based off of the CruWear one I listed first. Both handle shapes feel comfy in the hand! The blade shape is similar, but the Magnacut/CruWear ones have a more slender/pointy blades and the different handle, so I may call those the Bird and Trout model and the other is the EDC3 model.

These are my EDC 4 and EDC 3 blanks from NJSB. The EDC 4 is made as a 4" blade, full size, wider handle that I can trim down to the EDC 3 model as well, which is why it has 2 sets of pin/lanyard holes.


This is what the EDC4 looks like done up.


This one is one of the EDC4 prototypes in 5/32" 52100, 62 HRC, with natural canvas micarta scales, black pins, liners and lanyard tube. There is some patina right in front of the handle from where the blade was taped off when I did some handle clean up, so I can let this one go for $175 if someone is interested! I have a bunch of the EDC4 in Nitro V and some in Magnacut as well that I haven't ground out yet as well as a few EDC3 in Nitro V left. I took a bunch of these to my Fish and Game Club Turkey shoots. Some loved the EDC 4 for hunting purposes, others loved the EDC3 and said the 4 was too big! LOL. Everyone has their own tastes!

 

[jfk1110]

Some great designs and results.....That last one looks damn comfy!!!!.
That #4 ....Drooling all over it....... Fine work all around