XM-18 3.0" Wharncliffe Tri-Way Working Finish with all genuine Hinderer extras
SOLD
$500 PayPal F&F or $520 PayPal G&S shipped USPS Priority
F&F preferred but we can work out another option if needed.
My only trade interest is an Umnumzaan Drop Point MagnaCut.
Working Finish 20CV Wharncliffe Blade with flipper delete done by Way of Knife. Show side is a smooth titanium Battle Blue scale, Battle Blue pivot screw and handle screws. Lock side is factory working finish with Battle Blue handle nuts and LBS. Comes with Working Finish Holey pocket clip, Flamed filler tab, and T8 "flat" head clip & tab screws from TiConnector. Currently has factory bearings installed but comes with Hinderer tri-way parts for bronze washers, and Skiff thick washers. No nylon washers are included. I have all original packaging for the knife and the parts, will not come with the bag for the flamed tab set as I am keeping the flamed clip (from clip/tab set) for another XM-18.
Flipper delete was done perfectly by WOK, perfectly following the outline of the handle when the blade is open. The area where the flipper was ground down is satin from being ground down but isn't really noticeable that its a different finish than the blade. Has a 20 degree edge from a Wicked Edge system, edge has seen some light use but is always stropped before put away. Blade is centered, action is super smooth, detent is perfect for finger flicking and not too firm for thumb flicking. Solid lock up with no lock stick and no blade play.
No signs of use on the blade except maybe a tiny tiny bit at the very tip. I was able to catch that in the photos well. There are light signs of carry on the titanium scale, pivot screw, and handle screws but nothing too noticeable and no gouges, just snails. All photos were taken directly under a 4000k light so everything shows up. No marring on any of the hardware.
More Photos: XM-18 Pics
Video: XM-18 Video
SOLD
$500 PayPal F&F or $520 PayPal G&S shipped USPS Priority
F&F preferred but we can work out another option if needed.
My only trade interest is an Umnumzaan Drop Point MagnaCut.
Working Finish 20CV Wharncliffe Blade with flipper delete done by Way of Knife. Show side is a smooth titanium Battle Blue scale, Battle Blue pivot screw and handle screws. Lock side is factory working finish with Battle Blue handle nuts and LBS. Comes with Working Finish Holey pocket clip, Flamed filler tab, and T8 "flat" head clip & tab screws from TiConnector. Currently has factory bearings installed but comes with Hinderer tri-way parts for bronze washers, and Skiff thick washers. No nylon washers are included. I have all original packaging for the knife and the parts, will not come with the bag for the flamed tab set as I am keeping the flamed clip (from clip/tab set) for another XM-18.
Flipper delete was done perfectly by WOK, perfectly following the outline of the handle when the blade is open. The area where the flipper was ground down is satin from being ground down but isn't really noticeable that its a different finish than the blade. Has a 20 degree edge from a Wicked Edge system, edge has seen some light use but is always stropped before put away. Blade is centered, action is super smooth, detent is perfect for finger flicking and not too firm for thumb flicking. Solid lock up with no lock stick and no blade play.
No signs of use on the blade except maybe a tiny tiny bit at the very tip. I was able to catch that in the photos well. There are light signs of carry on the titanium scale, pivot screw, and handle screws but nothing too noticeable and no gouges, just snails. All photos were taken directly under a 4000k light so everything shows up. No marring on any of the hardware.
More Photos: XM-18 Pics
Video: XM-18 Video
Last edited: