Sale Terms:
Please Note: To view full size of photos, click each one individually. To further expand, click on the magnifying glass located on the lower right hand of the image - this will open up the image again. Repeat the step, clicking again on the magnifying glass and this will open up the full size photo.
----------------------------------------------------------------------------------------
All below are sold:
1) Malkoff MD1 [Sold on another forum] $130
MD3 body that was cut down to MD1 size for use with a single 18350 battery by Martin D White. Has a new lens/gasket installed with the neutral white M361N XP-G2 3-mode module and a Hi/lo switch. There is a gap between the body and MD tailcap, I added an o-ring to help hide though the tailcap cannot be fully tightened this way as the o-ring will squish out (the light is still functional). Or if you don't mind the gap it can be tightened all the way without the o-ring.
4) Olight S10 [Sold on another forum] $35
Has a cool white XM-L2 emitter (leans a bit towards yellow in hotspot); magnet in tail. Has seen some pocket time, has a spec or two of ano missing (see photos). Very good condition. Includes box and all original accessories.
7) EagleTac D25Cvn Limited Edition Ti XP-G2 [Sold on another forum $98] $95
Uncarried, only tested.Modified by Wayne (vinhnguyen54). Dedomed cool white emitter (now in the neutral realm). Doesn't throw as far as the XP-E2 version, but is no slouch in that area and brighter overall. Full disclosure: Pocket clip is slightly pitted at the bend (see photo), though less "severe." Comes with box, holster, and all accessories.
8) NovaTac 120P [Sold on another forum] $45
Purchased this a few weeks back on the exchange, this is the programmable model. Has a lovely cool white SSC P4 emitter. There is some light wear but nothing bad. It was fine when I received it and worked flawlessly for a couple of days. Unfortunately, it developed some issues with the switch. It misses clicks sometimes and requires a very firm/hard press for it to respond. Please watch the video to see what I began experiencing: http://s1313.photobucket.com/user/moshow9/media/temp/VIDEO0063_zpsmqnukyxk.mp4.html
I asked Henry if he might know what was going on and stated the switch could either be contaminated or the spring might be hanging up and not allowing a proper connection. He offered some advice on what I could try but I was unsuccessful in my attempts. I was even able to obtain two new springs from the last NovaTac lights but they didn't work. I figure someone else might be able to get it to work and if they can it would be a steal. Comes with what you see in the photos. It will need non-conducting grease on the threads/contacts.
**UPDATE** sween1911 over on CPFMP provided a fix to try via pm and cannot thank him enough. As of right now the tailcap and clicks are functioning as they should be, and do not require the firm/hard pressing. I will get a video up by tomorrow.
Flowchart/Programming Guide: http://files.bluecrow.net/flashlights/flowcharts/Novatac 120P Flowchart v0.5.pdf
- Ships First Class mail in a bubble wrapper (wrapped very secure) unless otherwise specified - Priority Mail upgrade is available for an additional $3
- US shipping on this one only (for ease of shipping while I continue to recover)
- Paypal Purchase of Goods Option (no gift payments please)
- Paypal payment must be received within 12hrs unless previously discussed
- I reserve the right to refuse sale at my discretion
Please Note: To view full size of photos, click each one individually. To further expand, click on the magnifying glass located on the lower right hand of the image - this will open up the image again. Repeat the step, clicking again on the magnifying glass and this will open up the full size photo.
----------------------------------------------------------------------------------------
All below are sold:
1) Malkoff MD1 [Sold on another forum] $130
MD3 body that was cut down to MD1 size for use with a single 18350 battery by Martin D White. Has a new lens/gasket installed with the neutral white M361N XP-G2 3-mode module and a Hi/lo switch. There is a gap between the body and MD tailcap, I added an o-ring to help hide though the tailcap cannot be fully tightened this way as the o-ring will squish out (the light is still functional). Or if you don't mind the gap it can be tightened all the way without the o-ring.
4) Olight S10 [Sold on another forum] $35
Has a cool white XM-L2 emitter (leans a bit towards yellow in hotspot); magnet in tail. Has seen some pocket time, has a spec or two of ano missing (see photos). Very good condition. Includes box and all original accessories.
7) EagleTac D25Cvn Limited Edition Ti XP-G2 [Sold on another forum $98] $95
Uncarried, only tested.Modified by Wayne (vinhnguyen54). Dedomed cool white emitter (now in the neutral realm). Doesn't throw as far as the XP-E2 version, but is no slouch in that area and brighter overall. Full disclosure: Pocket clip is slightly pitted at the bend (see photo), though less "severe." Comes with box, holster, and all accessories.
8) NovaTac 120P [Sold on another forum] $45
Purchased this a few weeks back on the exchange, this is the programmable model. Has a lovely cool white SSC P4 emitter. There is some light wear but nothing bad. It was fine when I received it and worked flawlessly for a couple of days. Unfortunately, it developed some issues with the switch. It misses clicks sometimes and requires a very firm/hard press for it to respond. Please watch the video to see what I began experiencing: http://s1313.photobucket.com/user/moshow9/media/temp/VIDEO0063_zpsmqnukyxk.mp4.html
I asked Henry if he might know what was going on and stated the switch could either be contaminated or the spring might be hanging up and not allowing a proper connection. He offered some advice on what I could try but I was unsuccessful in my attempts. I was even able to obtain two new springs from the last NovaTac lights but they didn't work. I figure someone else might be able to get it to work and if they can it would be a steal. Comes with what you see in the photos. It will need non-conducting grease on the threads/contacts.
**UPDATE** sween1911 over on CPFMP provided a fix to try via pm and cannot thank him enough. As of right now the tailcap and clicks are functioning as they should be, and do not require the firm/hard pressing. I will get a video up by tomorrow.
Flowchart/Programming Guide: http://files.bluecrow.net/flashlights/flowcharts/Novatac 120P Flowchart v0.5.pdf
Last edited:
