Ti Framelock and Ti Flipper @@Both SOLD@@

[J. Hoover]

This one is sold, , thanks
Finally got around to finishing this one today. The blade on this one is very slightly off center for some reason, about the width of the point. So I'll be letting it go
for less than I would have preferred considering the time and materials that I have in it. It opens and closes easily. Lockbar operates smoothly, the blade
locks up early and is bank vault tight. Here are the specs for this hand made custom:

Steel- CPM154 x .125
Closed- 4 7/8 inches
Open- 8 1/2 inches
Blade- 3 3/4 inch clip point with drawn swedge and jimping
HT- in house with dry ice cryo to a tested 59-60rc
Finish- hand sanded and bead blasted with stone washed bevels and bright flats
Frame- .150 machined titanium that was hand sanded, bead blasted then stone washed
Pivot- Blue anodized 3/16 titanium
Clip- machined blue anodized titanium set up for right hand tip up carry
Thumbstud- Hand turned blue anodized titanium
Lanyard- custom florescent
Hardware- Stainless
Asking 330.00 shipped in the USA
Paypal, USPS M/O, or Certified Check preferred
Questions or comments welcomed
Thanks for looking

Next: This one is SOLD, thanks
Carbon Fiber and Titanium Flipper
This one has a perfectly centered blade, and bank vault tight lock up. It fires every time with no wrist flip and sounds great doing it. The modified wharnie blade has a tactical look and is razor scary shaerp.
Here are the specs on this one of a kind customer flipper:

Steel- cpm154 x .156
Closed 4 3/4 inches
Open- 8 1/4 inches
Blade- 3 5/8 inches
Grind- Flade ground with swedge; fullers, and jimping
HT- in house to a tested 59-60 rc
Edge- polished convex edge is scary sharp
Frame- Lock side is .150 stonewashed titanium, presentation side is .100 anodized titanium and black carbon fiber
Pivot- 3/16 stainless with anodized titanium screws phosphor bronze washers
Stop Pin- 3/16 heat treated 416 stainless
Lanyard- Lanyard included is requested
Clip- Machined custom anondized titanium set upi for tip up right hand carry
Hardware- stainless
Asking 350.00 shipped in the USA
Paypal, USPS M/O, or Certified check preferred
Questions or comments welcomed

Thanks for looking

Video link, not the best quality but you can see the action.

 

[asdf12345]

I like this knife a lot. I think the design and aesthetic shows greater maturity than that of your previous knives. Great stuff!

 

[bb6tuner]

Mr Hoover, I'll take the non flipper!
I have paypal whenever you are ready sir.

 

[VA Knife Addict]

Both of these are sweet! I think the CFTF just may be the coolest knife you've made. If I am lucky this one will be available later today for me to snatch up. Great job yet again Hoover!

 

[J. Hoover]

Thanks bb6tuner, its yours. I responded to your pm.

Va Knife Addict thanks for the kind words, hopefully it will be yours.

 

[velodemon]

I am not I the market for a new knife right now but I just wanted to say, those are by far, the nicest looking folders I have seen you post. The action on the flipper looked incredible. Great work! Please keep it up!!!!

 

[arrowhd]

Very nice looking framelock. Looks very functional.

 

[abiggs]

I'll take the framelock flipper. That is a thing of beauty! Email me your PP address and I will get it coming!

 

[J. Hoover]

It's yours abiggs, thanks. Email sent

 

[VA Knife Addict]

I waited too long. I have no doubt that I will own one of your knives in the near future. Keep making quality stuff Hoover!

 

[JR88FAN]

Really liking that flipper, hope to see more in the near future.

 

[SpearZ]

Really like your design and materials, well done!