Users: ZT 0350CB, Spyderco Endura(Krein FFG), CS Talwar

[Noctis3880]

-All knives unless otherwise noted have been carried, used, and sharpened.
-Paypal Personal only.
-USPS Priority Shipping to CONUS only, insured.
-I have a Macro lens, so I can take detailed pictures if requested(still kinda new at it though).


Spyderco Endura
Knife has been reground(FFG) by Tom Krein. Blade is semi mirror polished with a slight orange peel texture. Clip has been polished on one side only.

Note: Tip has been chipped off twice and reground. This blade is extremely thin and delicate! Don't buy unless you're aware of the care needed for such a thin and extremely hard knife!

Asking $105$85 shipped.

Kershaw Speedform
Serial #248. Blade was rubbed down with Brasso. Touched up on slotted paper wheels, but some of the factory grind lines are still visible.

Note: Handles have been slightly polished at a small spot near the blade due to contact with paper wheels when sharpening.

Asking Withdrawn shipped.

Pictures attached.

 

[Noctis3880]

Cold Steel Talwar
Blade has been scuffed slightly on both sides from rubbing against the inside of the handles. Could be possible to buff off, but that could be difficult to do without buffing off the print on the blade(bead blasting would make it more resistant to scratching). Titanium bolster has also be scuffed a little from pocket carry. Edge has been stropped on diamond paste, but the factory grind lines are still clearly visible. This has not been seriously sharpened or used, just carried. Includes hard storage case and extra clip/screws.

Asking $205$200 shipped.

 

[Noctis3880]

Benchmade 635 Mini-Skirmish
I am not the original owner of this knife. There is a single scratch line on one side of the blade from the last owner's attempt at sharpening, it is barely visible and will not show up in photos(requires a good light up close in order to spot). Clip side of the handle has some scratch marks on the lockbar, clip has some black spots that won't come off(could be either rust or something else, but it should be possible to buff off). Non-clip side has a shiny scuff mark near the pivot screw.

Note: Handles are slightly polished at a small spot near the blade due to contact with paper wheels.

Asking SOLD shipped.

 

[Noctis3880]

Zero Tolerance 0350CB
Serial #0580. Asking $130SPF shipped.

Zero Tolerance 0350CB(second)
Serial #0565. This one had the screw stripped on the pocket clip when I attempted to move it from tip down to tip up carry. The screw is still in there and I had the pocket clip attached with Arctic Alumina thermal epoxy in tip up carry position. Other than that, the knife is 100% functional. Blade has also been polished up a little bit on buffing wheels.

Asking $80$75 shipped.

The "defective" one is the one without a lanyard(see photos).

 

[Noctis3880]

Emerson Super Karambit
Lockup is at about 50%. Clip has been moved for right side reverse grip.

Note:
Backbevel has been slightly mirror polished, but not the rest of the blade, so it looks somewhat inconsistent. The flat side of the blade is also somewhat similar, with a mostly stonewashed finish and then a small portion that is mirror finished near the edge from the paper wheels.

Asking $155SPF shipped.

 

[Noctis3880]

Skirmish is SPF.

 

[marucusu]

seconds on Skirmish if it falls through...

 

[CTS-Veo]

I'll take the first ZT if it's still available. I cant reply to a PM yet, but you can PM me your email address.

 

[Noctis3880]

Skirmish is SOLD.

 

[Noctis3880]

I'll take the first ZT if it's still available. I cant reply to a PM yet, but you can PM me your email address.

Visitor message left.

 

[Falcor]

I don't use the pocket clip on folders so the 2nd ZT 0350CB suits me fine - however, can you confirm that the white stuff you have used will come off cleanly?
Thanks
BP

 

[Noctis3880]

I don't use the pocket clip on folders so the 2nd ZT 0350CB suits me fine - however, can you confirm that the white stuff you have used will come off cleanly?
Thanks
BP

It is epoxy, so I sincerely doubt it.

 

[Falcor]

OK - I though so but was hoping. Thanks

It is epoxy, so I sincerely doubt it.

 

[riggerrobert]

Emerson Super Karambit -- I will take it, per our email. Thanks

 

[Noctis3880]

Super Karambit and ZT 0350CB(the good condition one) are SPF.

 

[Noctis3880]

Speedform withdrawn.