This one is SOLD fellows, thanks
Lets try to send this one to a new home, 215.00 shipped in the USA for limited time!!!!!!!!
Made this one a few days ago using some of Aldo's 5160 steel. It's named for toughness not as a battle knife although it certainly would work in that arena. Intended for hard cutting and chopping camp knife it is shaving sharp. The kydex sheath is set up for your large tek-lok, right/left, vertical or horizontal carry.
Heat treat was a full quench with the spine of the blade drawn back after hardening. Here are the specs:
Steel- 5160 X .250
AOL- 14 inches
Grind- Flat
Blade- 8 inch sharpened edge with drawn swedge
Finish- Hand sanded to 2000 grit
Handle- 5 3/4 inches
Scales- Black Canvas Micarta
Hardware- Stainless Loveless bolts with stainless lanyard tube
Sheath- .80 Black Kydex set up for YOUR large Tek-lok, left/right. vertical or horizontal carry
Asking 250.00 shipped in the USA or Canada
Paypal, USPS M/O, or Certified Check preferred
Questions or comments welcomed
Thanks for looking
I'll Take it in thread buys it
Bushcrafter is SOLD
Next up is a bushcrafter I finished recently. This one is CPM3V tool steel with a full scandi grind. Here are the specs:
Steel- CPM3v X .145
AOL- 10 inches
Grind- Scandi
Blade- 5 inch sharpened edge
Finish- Hand sanded flats with scotchbrite on grinds
Handle- 4 7/8 inches
Scales- Stabilized Masur Birch with black G10 liners
Hardware- Loveless stainless bolts and stainless lanyard tube
Sheath- .80 black kydex set up for YOUR Large Tek-Lok. Blade can be carried right/left, vertical/horizontal either handle up or handle down. Multiple locations for your tek-loc
Asking 150.00 shipped in the USA or Canada
Paypal, USPS M/O, or Certified Check preferred
Questions or comments welcomed
Thanks for looking
I'll Take it in post buys it
Lets try to send this one to a new home, 215.00 shipped in the USA for limited time!!!!!!!!
Made this one a few days ago using some of Aldo's 5160 steel. It's named for toughness not as a battle knife although it certainly would work in that arena. Intended for hard cutting and chopping camp knife it is shaving sharp. The kydex sheath is set up for your large tek-lok, right/left, vertical or horizontal carry.
Heat treat was a full quench with the spine of the blade drawn back after hardening. Here are the specs:
Steel- 5160 X .250
AOL- 14 inches
Grind- Flat
Blade- 8 inch sharpened edge with drawn swedge
Finish- Hand sanded to 2000 grit
Handle- 5 3/4 inches
Scales- Black Canvas Micarta
Hardware- Stainless Loveless bolts with stainless lanyard tube
Sheath- .80 Black Kydex set up for YOUR large Tek-lok, left/right. vertical or horizontal carry
Asking 250.00 shipped in the USA or Canada
Paypal, USPS M/O, or Certified Check preferred
Questions or comments welcomed
Thanks for looking
I'll Take it in thread buys it
Bushcrafter is SOLD
Next up is a bushcrafter I finished recently. This one is CPM3V tool steel with a full scandi grind. Here are the specs:
Steel- CPM3v X .145
AOL- 10 inches
Grind- Scandi
Blade- 5 inch sharpened edge
Finish- Hand sanded flats with scotchbrite on grinds
Handle- 4 7/8 inches
Scales- Stabilized Masur Birch with black G10 liners
Hardware- Loveless stainless bolts and stainless lanyard tube
Sheath- .80 black kydex set up for YOUR Large Tek-Lok. Blade can be carried right/left, vertical/horizontal either handle up or handle down. Multiple locations for your tek-loc
Asking 150.00 shipped in the USA or Canada
Paypal, USPS M/O, or Certified Check preferred
Questions or comments welcomed
Thanks for looking
I'll Take it in post buys it
Last edited:
