Worm Bone - Hand Made Slip Joint Knife

T.A.DAVISON

T.A.DAVISON

Slip Joint Knife Maker
Feedback: +106 / =0 / -0
Joined
Oct 24, 2005
Messages
5,477
Custom Slip Joint Folder Knife.

.



Folder - #963

~~~ $500.00 ~~~
Sold - Thanks!


963AAA.jpg






Scales - Worm Jig Bone
Steel - 3/32'' ATS34 - Rc. 60 - 61
Bolsters & Liners - stainless
Shield - stainless - inlaid & dbl. pinned

Closed - 3 5/8''

Hollow ground ......... Hand Finished.......... Cryogenic Quenched
Closes dead center .......... Half Stop .......... Razor Sharp.
Nice walk & talk. ...... Shipped in a protective case.

You can say I'll take it here.
PayPal is preferred please.

Thanks for the looks - any question or comments are welcomed.


​
 
Last edited:
Mr. Davison,

Absolutely gorgeous folder, sir! Beautiful worm bone jig grove pattern. In fact, I have *never* liked the look of any (mass produced) worm bone, but I am very interested in purchasing this knife. I have a few questions, if you would not mind:

1) Blade length?
2) Would you describe the bolster to me or post an alternate picture? With the various shadows and reflections, I cannot tell if it is a double ringed, pinched, "indented" (??? I don't know if there is such a thing as "intented"; apologies, newbie to custom knives).
3) If I am seeing it correctly, it appears as though the hollow grind run the entire height of the blade, beginning just above the nail pull. Is this correct?

Thank you,
Annabell
 
annabellz82 said:
Mr. Davison,

Absolutely gorgeous folder, sir! Beautiful worm bone jig grove pattern. In fact, I have *never* liked the look of any (mass produced) worm bone, but I am very interested in purchasing this knife. I have a few questions, if you would not mind:

1) Blade length?
The Blade is - 2 7/8'' long.

2) Would you describe the bolster to me or post an alternate picture? With the various shadows and reflections, I cannot tell if it is a double ringed, pinched, "indented" (??? I don't know if there is such a thing as "intented"; apologies, newbie to custom knives).
The Bolster is fluted on side - look at top photo of knife and you see it's a single flute going across the bolster. (NOT double ringed or pinched?)

3) If I am seeing it correctly, it appears as though the hollow grind run the entire height of the blade, beginning just above the nail pull. Is this correct?
The blade is hollow gound very thin for a very sharp cutting edge. I grind the blades on a 14'' wheel.

Thank you,
Annabell
Click to expand...

Annabell,
I hope this answers your questions?
If you do want the knife - please send me $500.00 at.... crazyknifeblade@yahoo.com
Thanks!
 
If the deal with annabell falls through and you don't have any others that have expressed interest, I'll put in a backup I'll take it. I'll send you a PM with contact details.
 
T.A.DAVISON said:
You got it.
Please send me $500.00 at.... crazyknifeblade@yahoo.com
Marking it sold for you.
Thanks!
Click to expand...

Mr. Davison,

Apologies that I dragged ass and didn't get a reply sent to you in a timely fashion. I'm glad you got a solid offer/buyer for this knife. It's gorgeous piece! And thank you for answering all of my previous questions about this knife. I will be more prompt to reply in the future! Thanks again. :)

Kindest,
Annabell
 
You must log in or register to reply here.
Back
Top