WTS: Custom, Modified, and Stock Flashlights

[moshow9]

Something has come up and I am cutting back on my flashlight hobby, if not getting out for a while. Need these to go to a good home. If you have any questions, please feel free to ask.

Sale Terms:

• US/US territory shipping only, unless we have previously dealt before
  
• First Class shipping unless otherwise indicated
• Paypal Purchase of Goods Option (no gift payments please)
• I reserve the right to refuse sale at my discretion
• Not looking for trades

1) Airayaland mule light modified** $70 $75
2) FourSevens Mini Mk II Ti [Sold to ssgwhite] $40
3) JetBeam E20R [Sold to ssgwhite] $40
4) JetBeam Jet-II Pro [Sold to Foghorn Leghorn Fan] $30
5) JetBeam Jet-TH20 relisted
6) Muyshondt Aeon MkIII Aluminum (Deep Indigo) modified** relisted
7) Omicron** relisted
8) Tain Ottavino Ti 10280 v4 [On Hold] $325 ships priority
9) Thrunite T10T modified** [Sold on another forum] $75

**For lights with guppdydrv firmware see post for UI breakdown. ​

1) Airayaland modified
Emitter: MT-G2 Q0 5000K (neutral white). This is an AA flashlight modified to a high powered mule light by CRX. It uses guppydrv v1 with a FET-15. The switch is a forward clicky and has a green trit in the lanyard loop space. There is a green glow ring swapped in at the head as well. The inside of the body has been lined with carbon fiber to reduce battery rattle. Uses 2 14250 batteries, both included as a matched set.

Do not run on max unattended or for too long, gets very hot very fast as it is pushing about 1,600 lumens.

 

[moshow9]

2) FourSevens Mini Mk II Ti
Emitter: XM-L2 U3 (neutral white). This is brand new and still sealed. Beadblasted finish. Uses 1 CR123a or 16340 (not included).

3) JetBeam E20R
Emitter: SST-40 N4 BC (cool white). This is a catch and release. Small light with big output (listed 990 lumnes) with onboard micro usb charging (cable included). Includes box and all original accessories (16340 Jetbeam battery as well).

 

[moshow9]

4) JetBeam Jet-II Pro
Emitter: XP-L HI (cool white). Tested but uncarried. Has a nice cool white tint with decent throw thanks to the factory dedomed XP-L High Intensity emitter. Includes pocket clip with original accessories and box. Bezel ring can be taken off and swapped out for a strike bezel (included). Uses 1 CR123a battery or 1 RCR123/16340. I am including a rechargeable Nitecore RCR123a battery with it.

Full Disclosure: Depending on the length of time removed from the battery, each battery change can possibly place the light in electronic lockout mode. This is not a fault or defect, but is worth mentioning for someone who might be unaware of this feature. Also please note closeup of emitter, in the photo it looks like the bottom of the reflector is damaged but this is just a matter of the angle. The reflector is just fine without any damage.

UI while electronically locked out:
From off: Press and hold switch for 3 seconds to unlock light.
From off: Double click to moonlight. While on, a press and hold cycles only between the two modes of moonlight and High. A single click turns the light off.
From off or on: Triple click to access strobe.
From on: Quad click to set 3 minute timer (light turns off). Quad click again to set 9 minute timer.

UI while unlocked:
From off: Press and hold switch for 3 seconds to electronically lock the light out.
From off: Double click to moonlight. While on, a press and hold cycles only between the two modes of moonlight and High. A single click turns the light off.
From off: A single click turns the light on to the last memorized mode (default is High). While on, a press and hold cycles the light from Hight to Medium to Low.
From off or on: Triple click to access strobe.
From on: Quad click to set 3 minute timer (light turns off). Quad click again to set 9 minute timer.

Manual lockout can be achieved by slightly loosening the tailcap to break current connection. The UI might seem complicated at first but it isn't once you get the hang of it. It's really quite versatile.

5) JetBeam Jet-TH20
Emitter: XHP70.2 (cool white). Super bright! Has a momentary/constant on switch, with paddle switches along side main tail switch. Paddle switches adjust modes from Turbo, High, Med, and Low. A press and hold from either on or off will activate strobe. Includes box and all original accessories, along with Jetbeam battery.

 

[moshow9]

6) Muyshondt Aeon MkIII Aluminum (Deep Indigo) modified
Emitter: Nichia 219B (neutral white). This was modified by ShineOnYouCrazyDiamond with guppydrv Rev 1 firmware with a FET-15. Includes box and 4 x 15270 IMR batteries.

7) Omicron
Emitter: Nichia 219C 4000K (neutral white). Custom Ti light in a beadblasted finish. Firmware is guppydrv Rev 1. Runs off of a 10180 battery (1 included), along with box and split-ring. Tail end can take 6 1mm x 3mm tritium vials. Max output is around 200 lumens. Please excuse the blue velvet lint that stayed on the light when I removed it from it's pouch.

 

[moshow9]

8) Tain Ottavino Ti 10280 v4
Emitter: XP-L HI V2 4B (neutral white). Custom Ti mule light with aqua glow around the emitter and a blue trit at that tail. Uses 1 x 10280 battery. Tighten the light to turn off. Slightly loosen to turn on to low, loosen some more to change to high. Includes light holder, battery, 2 split rings (small and large), swivel, McGizmo clip, and a spare o-ring.

NOTE: Battery must go in positive in towards tail, negative end towards head. Failure to do so may fry the light as I do not believe it has reverse polarity.

 

[moshow9]

9) Thrunite T10T modified
Emitter: XHP50 J4 1A (cool white). This is an AA flashlight modified to a high powered light by CRX. It uses guppydrv v1 with a FET-15. The switch is a reverse clicky and has a green trit in the lanyard loop space. There is a green glow around the emitter. The inside of the body has been lined with carbon fiber and felt to reduce battery rattle. The body has graphite accents. Uses 2 14250 batteries, both included as a matched set.

Do not run on max unattended or for too long, gets very hot very fast as it is pushing about 1,600 lumens. Has carry marks.

guppydrv Rev1

 

[machineage]

Hello. Can the thrunite t10t operate with the AA or 14500 batteries? Thanks.

 

[moshow9]

Hello. Can the thrunite t10t operate with the AA or 14500 batteries? Thanks.

Hi machineage, unfortunately it cannot use AAA or a 14500. 2 lithium ion batteries in series are required to get it to run.

 

[Mainecobra]

Pm sent

 

[machineage]

Thanks moshow.

 

[ssgwhite]

PM sent for 2 & 3

 

[moshow9]

PM sent for 2 & 3

PM on the way.

 

[Foghorn Leghorn Fan]

I'll take # 4, sending PM

 

[moshow9]

I'll take # 4, sending PM

PM responded, SPF.

Edit: Payment received.

 

[bladeknot]

Subscribed. wish you were accepting trade offers..

 

[moshow9]

Some lights are still available and some new prices on a couple.