Hi all,
Haven't sold/traded here in a while, so please feel free to ask for references...I have some here, ebay, and other forums.
I got a new knife for Christmas and found a few knives cleaning out a drawer, so thought I would post these up.
Interested in the following knives:
-BM Stryker Axis (or similar BMs, but not grips or anything assisted)
-Any titanium William Henry with a pocket clip
-Jeremy Robertson (Calavera Cutlery) El Fuego
-CRKs
-Kingdom Armory Mini-Samaritan
-Anything else offered (worst I can say is no!)
Willing to add cash to trade for any of these. Willing to sell any of these outright.
Please ask any questions. I will post additional pictures in replies...
***SOLD***HK (Benchmade) 14700 - Auto***SOLD***
-3.75" black-coated 440C blade
-Received as a gift a few years ago. No box or anything.
-The handle is not too beat up, just some snail trails. The clip has lots of paint wear.
-The blade has some coating marks and the serrations are beat up pretty bad (see pictures)
-Knife was carried infrequently while I was in the Marine Corps. Still has factory edge and is fairly sharp.
-Action fires hard. Safety on spine works correctly.
***SOLD***Kershaw 1595alblk***SOLD***
-3.625" blade (think its Sandvik 13C26)
-Blade says 'Made in USA' and is stamped 'Dec 06'
-Handle is clean. Clip is clean.
-Blade has some light surface rust marks, a larger rust mark on the right side, and a strange stain pattern on the finish (no idea how/when that happened). Think this could be cleaned up pretty easily.
-Purchased a few years ago, hardly ever used. No box or any papers. Factory edge.
-Action works properly - blade snaps into place and locks cleanly.
William Henry EDC E10-3
-3.25" black coated D2
-Handle is black coated aluminum and has some wear marks where the coating is gone
-Blade is pretty clean, looks better than pictures.
-Received as a gift 5 years ago. Includes box and warrant card...never looked at the warranty card before, but it looks like it is for a different EDC E10.
-Blade swings cleanly and locks up cleanly with button.
-Carried daily for the past 2 years - I work in an office, so not too hard of use. Sharpened a few times on my edgepro - there is a small section of the edge that is not the same width as the rest of the knife, but it is overall clean and sharp.
Thanks for looking!
Haven't sold/traded here in a while, so please feel free to ask for references...I have some here, ebay, and other forums.
I got a new knife for Christmas and found a few knives cleaning out a drawer, so thought I would post these up.
Interested in the following knives:
-BM Stryker Axis (or similar BMs, but not grips or anything assisted)
-Any titanium William Henry with a pocket clip
-Jeremy Robertson (Calavera Cutlery) El Fuego
-CRKs
-Kingdom Armory Mini-Samaritan
-Anything else offered (worst I can say is no!)
Willing to add cash to trade for any of these. Willing to sell any of these outright.
Please ask any questions. I will post additional pictures in replies...
***SOLD***HK (Benchmade) 14700 - Auto***SOLD***
-3.75" black-coated 440C blade
-Received as a gift a few years ago. No box or anything.
-The handle is not too beat up, just some snail trails. The clip has lots of paint wear.
-The blade has some coating marks and the serrations are beat up pretty bad (see pictures)
-Knife was carried infrequently while I was in the Marine Corps. Still has factory edge and is fairly sharp.
-Action fires hard. Safety on spine works correctly.
***SOLD***Kershaw 1595alblk***SOLD***
-3.625" blade (think its Sandvik 13C26)
-Blade says 'Made in USA' and is stamped 'Dec 06'
-Handle is clean. Clip is clean.
-Blade has some light surface rust marks, a larger rust mark on the right side, and a strange stain pattern on the finish (no idea how/when that happened). Think this could be cleaned up pretty easily.
-Purchased a few years ago, hardly ever used. No box or any papers. Factory edge.
-Action works properly - blade snaps into place and locks cleanly.
William Henry EDC E10-3
-3.25" black coated D2
-Handle is black coated aluminum and has some wear marks where the coating is gone
-Blade is pretty clean, looks better than pictures.
-Received as a gift 5 years ago. Includes box and warrant card...never looked at the warranty card before, but it looks like it is for a different EDC E10.
-Blade swings cleanly and locks up cleanly with button.
-Carried daily for the past 2 years - I work in an office, so not too hard of use. Sharpened a few times on my edgepro - there is a small section of the edge that is not the same width as the rest of the knife, but it is overall clean and sharp.
Thanks for looking!
Last edited:
