Time to Change Your Snark Plugs

[Noswad0208]

This thread is getting closer to completion... Looking back for the snarkiest snarks and there isnt a while lot of snarking each other this go around... So far Guyon stinking up the the continent of the Americas is some of the funniest stuff, and its not really snarking...

We need to pick it up, id hate to run a RNG.

Hurt feelings, crush spirits, and make the other 'heads your -BEEP-.

We all conspired and promised not to snark too heavily just to confound you.

 

[Noswad0208]

Holy crap, I already have 1,050 posts. :foot:

 

[tradewater]

And a very happy St. Paddy's Mr. O'Murphy.

 

[Jerry D.]

Happy St. Patrick's day, folks.

 

[Noswad0208]

I'll be handing out pinches all day. Happy St. Patrick's.

 

[worldwood]

We all conspired and promised not to snark too heavily just to confound you.

This is believable!!


What are the bits called that cut larger circular holes in wood?? I dont see too many 3/4" or 1" drill bits.... But i need to cut 1- 1" circle and 6- 3/4" circles into a piece of wood about 5-6" in diameter and maybe 1" thick.

Thanks for the info... I know i have seen them, just cant think of what they hell they are called.

 

[Guyon]

 

[worldwood]

Happy St. Patrick's day

I'll be handing out pinches all day. Happy St. Patrick's.

I said it on FB and ill say it again here, if you guys live in a place where grown men run around pinching other grown men you might wanna reevaluate your location

 

[Noswad0208]

Happy St. Patrick's day



I said it on FB and ill say it again here, if you guys live in a place where grown men run around pinching other grown men you might wanna reevaluate your location

But I'm not a grown man.

 

[Jerry D.]

What are the bits called that cut larger circular holes in wood?? I dont see too many 3/4" or 1" drill bits.... But i need to cut 1- 1" circle and 6- 3/4" circles into a piece of wood about 5-6" in diameter and maybe 1" thick.

Thanks for the info... I know i have seen them, just cant think of what they hell they are called.

Are you looking for a spade bit, boring bit, or a hole saw?

 

[worldwood]

Are you looking for a spade bit or a hole saw?

Spade, thats it!! Thanks brother!!

 

[granitestateofmind]

This is believable!!


What are the bits called that cut larger circular holes in wood?? I dont see too many 3/4" or 1" drill bits.... But i need to cut 1- 1" circle and 6- 3/4" circles into a piece of wood about 5-6" in diameter and maybe 1" thick.

Thanks for the info... I know i have seen them, just cant think of what they hell they are called.

Spade, thats it!! Thanks brother!!

Hole saws are more accurate than spade bits (also more expensive) but in between the two there would be forstner bits and augers. Geeked out on hole making implements, I am.

 

[Jerry D.]

Hole saws are more accurate than spade bits (also more expensive) but in between the two there would be forstner bits and augers. Geeked out on hole making implements, I am.

*Light bulb* Forstner bits! That was the other one I was searching for in my head. Boring bit was all that came to mind.

 

[Noswad0208]

Geeked out on hole making implements, I am.

 

[granitestateofmind]

Happy Lá Fhéile Pádraig, Murph. Remember: the reason the Irish fight each other is they can find no other worthy opponents.

 

[Noswad0208]

Everyone, post Irish music!

WOO!

[video=youtube;HgpcNpOlxJA]https://www.youtube.com/watch?v=HgpcNpOlxJA&index=3&list=PL9E698FB72375F173[/video]
[video=youtube;T_hKLKpfdI0]https://www.youtube.com/watch?v=T_hKLKpfdI0&list=PL9E698FB72375F173&index=4[/video]
[video=youtube;L0L5geWlWgc]https://www.youtube.com/watch?v=L0L5geWlWgc&list=PL9E698FB72375F173&index=8[/video]

 

[Noswad0208]

[video=youtube;pkuwoc4VUag]https://www.youtube.com/watch?v=pkuwoc4VUag&list=PL9E698FB72375F173&index=10[/video]

 

[worldwood]

Hole saws are more accurate than spade bits (also more expensive) but in between the two there would be forstner bits and augers. Geeked out on hole making implements, I am.

Thanks for the info brother!!

Im just wanting to make a basic stand, but now that i re-check it its not 1", its about 1.2".... So ill prolly need a 1.25" spade bit and a 3/4" spade bit.

This is the idea.. Pretty basic... Just need to get the bits for the holes.

 

[Jerry D.]

Thanks for the info brother!!

Im just wanting to make a basic stand, but now that i re-check it its not 1", its about 1.2".... So ill prolly need a 1.25" spade bit and a 3/4" spade bit.

This is the idea.. Pretty basic... Just need to get the bits for the holes.

Why are your ovals all different sizes?

 

[Noswad0208]

Why are your ovals all different sizes?

Because it's windows paint, no one in the history of man kind has ever been able to do a decent oval on paint.

Also, here's a game to make you get angry at your computer.

tiny hat game