Order of KAI Official Hang Out; Good Times & Joyous Knives

[TotalDbag]

When you push the pivot housing back does the other scale push away?

 

[KnottyEagle]

Everything is lined up properly?

Yes, everythings lined up properly. Everything is going where it should. When I've got everything in their holes, and sandwhich them together, the little tube that the pivot screw screws into just pop out of place like in the picture.

 

[seelow123]

You might be hitting a washer when you try to push the female pivot piece in.

 

[KnottyEagle]

When you push the pivot housing back does the other scale push away?

What scale are you talking about? The non-locking side or the locking side? Everything looks normal except the pivot housing keeps popping out when I'm sandwiching the non-locking side scale to the blade and locking side scale.

 

[TotalDbag]

You might be hitting a washer when you try to push the female pivot piece in.

That's what I was thinking.

 

[TotalDbag]

What scale are you talking about? The non-locking side or the locking side? Everything looks normal except the pivot housing keeps popping out when I'm sandwiching the non-locking side scale to the blade and locking side scale.

Does it sandwich correctly without the washers?

 

[KnottyEagle]

I know for sure I'm not hitting a washer. I just tried to put it back together again and the same thing keeps happening.

 

[seelow123]

I would stop trying to sandwich it and take out the blade and washers. take off the non locking side and all the hardware that goes with it. Push the female pivot through, add locking side washers, add blade, add non locking side washers and then your scale and such. I don't know if that's what you are doing or if you've already done that.

 

[TotalDbag]

I would stop trying to sandwich it and take out the blade and washers. take off the non locking side and all the hardware that goes with it. Push the female pivot through, add locking side washers, add blade, add non locking side washers and then your scale and such. I don't know if that's what you are doing or if you've already done that.

:thumbup:

 

[BobSig]

Wow, black is awesome

 

[TotalDbag]

I really wish I had a cryo in my hands right now. It would be a lot easier to help.

Wow, black is awesome

Welcome to the club, AND!!!!!!!! That's what she said.

 

[BobSig]

That's what she said.

Dang it

 

[chester22]

What do you have coming in? Must be something really cool.

Some things that are composite ...and something to "offset" the weigh of the box...

 

[xICEMANx]

Alright who outbid me on that Damascus Leek on the bay?

 

[greeenie]

O, sorry that was me

 

[TotalDbag]

Some things that are composite ...and something to "offset" the weigh of the box...

I don't get it.

 

[BobSig]

Some things that are composite ...and something to "offset" the weigh of the box...

You have my attention

 

[BobSig]

Isn't that leek a lot?

 

[KnottyEagle]

I would stop trying to sandwich it and take out the blade and washers. take off the non locking side and all the hardware that goes with it. Push the female pivot through, add locking side washers, add blade, add non locking side washers and then your scale and such. I don't know if that's what you are doing or if you've already done that.

I did this and screwed in the pivot and the body screws, but the pivot housings still popped out like in the photo, but it's not popped out as far. The blade is off-center and barely touching the liner now.

 

[TotalDbag]

I did this and screwed in the pivot and the body screws, but the pivot housings still popped out like in the photo, but it's not popped out as far. The blade is off-center and barely touching the liner now.

So it was flush until you started to screw the male pivot in?