Joe Allen Knives

[Joe Allen Knives-2017]

OK Matt , will see about the slim line I have the pattern already , you need to think about scales. or have we already had this chat before heheheheeh!! Mammoth maybe .

 

[matt009au]

OK Matt , will see about the slim line I have the pattern already , you need to think about scales. or have we already had thios chat beforew heheheheeh!! Mammoth maybe .

I can't say no to ivory!

 

[Joe Allen Knives-2017]

 

[Joe Allen Knives-2017]

Hi Matt, hope all is well. I can send messages ,but do not have photo availble.

 

[matt009au]

Thought I'd post the pics for you mate

 

[Joe Allen Knives-2017]

Thanks Matt for posting.

 

[Joe Allen Knives-2017]

Hi everyone , here is a nice sunken joint Trapper I just finnished today . I used CPM-154 steel for the blade after heat treat an nitro quench an tempers I have a nice 60 Rc. The closed length is 3 7/8" with and open of 7". There is no spine showing or to feel when closed (Sunken Joint ) Nice burl Box Elder stabilized with and Inlaid Badge Shield and and a fileworked fluted bolster make this knife a stand out beauty. Blade lays perfect center and did so thru the whole work process ( Thanks to a Surface Grinder ). I do not notice any circles or rings anywhere after opening an closing up to 30 times, razor sharp and ready to work or go into a nice collection. will be posting in makers for sale area later. Thanks for looking an hope it makes your day in some way. Joe Allen.

 

[jd_elam]

Another great looking knife Joe!

 

[Joe Allen Knives-2017]

Thanks JD, yes it as close to perfect as I can get them. Has a 3 to 4 pull which is easy on the finger nails somewhat.

 

[Blackdogfinn1]

Really like the sunken joint! Real pocket friendly. Nice job and great work!

 

[Joe Allen Knives-2017]

Thanks Black Dog, the front bolsters are slightly rounded an burnished then hand polished to keep them from chewing your pockets up also with the Sunken joint . Thanks Again.

 

[Joe Allen Knives-2017]

Hi knife fans, here is my latest creation. A nice Easy Opener in Maroon Burlap and Cpm-154 steel blade an spring. Closed length is 3 3/4" short with 2 3/4" blade. Go to folders for sale section for more info . There is better photo's of this same knife below . Thanks everyone for looking . Joe

 

[Joe Allen Knives-2017]

HERE IS MORE PHOTO'S OF THE EASY OPENER-CONTINUED FROM PREVIOUS THREAD

 

[Joe Allen Knives-2017]

Hi Slip Joint lovers, I just finished this sweet Sepentine Jack in Oak Bog handle scales, and thought you might like to see a nice custom in the for sale area going for what some factory Case knives are selling for now days. 3.5 closed length. 6000 grit polished bolsters an inside spring. Satin finished blade. Opening pull about 4 with good snap in all three Flush positions. Go to knife makers section for more details if your into customs. Thanks for looking

 

[Joe Allen Knives-2017]

Hi everyone ! I have here today a nice Dog Leg Jack in Amber Jigged bone . The blade steel and spring are CPM-154 stainless steel. 3 1/2" closed . The Blade is hardened to about 63 rc then double tempered down to 60 -61 rc with Cryo quenched in between the tempers. Blade is hand sanded to 6000 grit going thru many grit sizes after several belt sizes did their job first. The inside spring is belt an hand sanded to 6000 grit with the blade hand sanded to 1000 grit. Fit an finish are emasculate. For more info if interested go to knifemakers for sale section under ( folders ) . Thanks for looking .

 

[abcdef]

Just a shout out. I have been enjoying looking at your work.

 

[Will Power]

Some original and interesting stuff you're making, getting a sunk-joint made is impressive-lot of makers seem to dodge that one...

 

[Joe Allen Knives-2017]

Thanks ABCDEF and Will , Appreciate the Kind remarks.

 

[Joe Allen Knives-2017]

El LOBO # 1- Hi slip joint friends , Finished this knife today an just showing it on my site, haven't made anything for quite a while. I Got the idea from a Ruffin Johnson knife which was a lock back , an I turned it into a slip joint . Knife is 4 3/16" " closed and 7 1/4" opened. Steel is CPM-154 an Has been Cryo treated between tempers. The scales are Box Elder Stabilized an the opening pull hardness is around 5 . Flush in all three positions. Just a sweet knife that I'm taking orders for if anyone might want this style with whatever scales you might want. Stainless bolsters hand finished to 6000 grit and blade 1000 grit. Email me at joeallen@me.com or pm or say something here. Comments welcomed. Most prices are 400.00 to 500.00 for this knife depending on extra's an scale materials. Thanks for Looking , Joe

 

[Joe Allen Knives-2017]

Eureka Jack Larger version.Here's the latest Eureka Jack from Me, this one is almost the same as the one I made last year except this one has the long pull and is 4 1/8" closed and right aT 7" Opened , where as the first one was around 3 3/4" closed. Has Stabilized Box Elder scales which are Awesome . The blade steel is CPM-154 at 60 Rc after heat treat -Cryo an tempers. Has a very nice smooth opening pull in all three positions at around 3 to 4 on pull. Walks an Talks like a jewell. Hope you like it.